1. Home
    2. /
  2. Manuals
    3. /
  3. Cisco
    4. /
  4. ECP3940ADL
    5. /
  5. 7
Page 31 / 54 Scroll up to view Page 26 - 30
Installation Preparations
OL-30773-01
13
Where Is the Best Location for My Wireless Residential Voice Gateway?
The ideal location for your residential gateway is where it has access to outlets and
other devices. Think about the layout of your home or office, and consult with your
service provider to select the best location for your residential gateway. Read this
user guide thoroughly before you decide where to place your residential gateway.
Consider these recommendations:
Choose a location close to your computer if you will also use the residential
gateway for high-speed Internet service.
Choose a location that is near an existing RF coaxial connection to eliminate the
need for an additional RF coaxial outlet.
Choose a location that is relatively protected from accidental disturbance or
harm, such as a closet, basement, or other protected area.
Choose a location so that there is plenty of room to guide the cables away from
the residential gateway without straining or crimping them.
Choose a location that allows adequate ventilation around the residential
gateway.
Choose a location for the residential gateway that is adjacent to your telephone
equipment if you plan on connecting your phone directly to the residential
gateway.
Note:
If you are using the residential gateway to provide service to several
telephones, a professional installer can connect the residential gateway to your
existing home telephone wiring.
How Do I Mount the Wireless Residential Voice Gateway on a Wall? (Optional)
Your residential gateway may include mounting holes so that, if you wish, you can
mount the residential gateway to a wall. This section describes how to mount the
residential gateway to a wall, and includes a list of the equipment that you will need
along with suggestions for choosing an appropriate place to mount the residential
gateway.
Page 32 / 54
Chapter 2
Installing the EuroDOCSIS Wireless Residential Gateway with Voice
14
OL-30773-01
Select an Appropriate Place to Mount the Wireless Residential Voice Gateway
You may mount the residential gateway to a wall that is made of cement, wood, or
drywall. When choosing an appropriate mounting place, refer to the following
recommendations:
Ensure that the mounting location is free of obstructions on all sides, and the
cables should be able to easily reach the residential gateway without strain.
Leave sufficient clearance between the bottom of the residential gateway and any
flooring or shelving underneath to allow access to cabling.
Allow enough slack in all cables so that the residential gateway can be removed
for any required maintenance without disconnecting the cables.
Choose a location that allows adequate ventilation around the residential
gateway.
Equipment Needed
Verify that you have the following items that you will need to mount the residential
gateway:
Two wall anchors for #8 x 1-inch screws
Two #8 x 1-inch pan head sheet metal screws
Drill with a 3/16-in. (4.8 mm) wood or masonry bit, as appropriate for the wall
composition
A copy of the wall-mounting slots illustration shown on the following pages
Page 33 / 54
Installation Preparations
OL-30773-01
15
Location and Dimensions of the Wall-Mounting Slots
The following illustration shows the location and dimensions of the wall-mounting
slots on the side of the residential gateway. Use this illustration as a guide for
mounting the residential gateway to the wall.
Note:
Image not to scale.
Page 34 / 54
Chapter 2
Installing the EuroDOCSIS Wireless Residential Gateway with Voice
16
OL-30773-01
Mounting the Wireless Residential Voice Gateway on a Wall
1
Using a drill with a 3/16-in. (4.8 mm) bit, drill two holes at the same height and 4
in. (101.6 mm) apart.
Note:
The preceding graphic illustrates the location of the mounting holes on the
back of the residential gateway.
2
Are you mounting the residential gateway into a drywall or concrete surface
where a wooden stud is available?
If
yes
, go to Step 3.
If
no
, drive the anchor bolts into the wall, and install the mounting screws
into the anchor bolts; leave a gap of about 1/2-in. (12.7 mm) between the
screw head and the wall. Then, go to Step 4.
3
Install the mounting screws into the wall; leave a gap of about 1/2-in. (12.7 mm)
between the screw head and the wall. Then, go to Step 4.
4
Verify that no cables or wires are connected to the residential gateway.
5
Lift the residential gateway into position. Slip the large end of both mounting
slots (located in the side of the residential gateway) over the mounting screws,
and then slide the residential gateway down until the narrow end of the keyhole
slot contacts the screw shaft.
Important:
Verify that the mounting screws securely support the residential
gateway before you release the unit.
Page 35 / 54
Install the Wireless Residential Voice Gateway
OL-30773-01
17
Install the Wireless Residential Voice Gateway
This section describes how to connect your residential gateway to support the
services that the residential gateway offers.
Connect Devices to the Wireless Residential Voice Gateway
The following illustration shows all of the possible connections that can be made to
your residential gateway for various services. Although your model may not
support all of the services pictured, you can determine which services your model
supports by referring to the Benefits and Features list in
Introduction
(on page 2).
Notes:
Professional installation may be available. Contact your local service provider for
further assistance.
Device image varies according to model.
Gateway Model EPC3940 shown in abov e example

Rate

4 / 5 based on 1 vote.

Popular Cisco Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top