Page 16 / 120 Scroll up to view Page 11 - 15
VoIP/(802.11g) ADSL2+ Router
Chapter 3: Basic Installation
15
Configuring PC in Windows NT4.0
1.
Go to
Start / Settings / Control Panel
. In the
Control
Panel, double-click
Network
and choose the
Protocols
tab.
2.
Select
TCP/IP Protocol
and click
Properties
. (
See Figure
3.12)
3.
Select the
Obtain an IP address from a DHCP server
radio
button and click
OK
. (
See Figure 3.13)
Figure 3.12: TCP / IP
Figure 3.13: IP Address
Page 17 / 120
VoIP/(802.11g) ADSL2+ Router
Chapter 3: Basic Installation
16
Factory Default Settings
Before configuring your, you need to know the following default settings.
Web Interface (Username and Password)
Username: admin
Password: admin
The default username and password are “
admin
” and “
admin
” respectively.
Attention
Attention
If you ever forget the password to log in, you may press the RESET button up to
6 seconds to restore the factory default settings.
LAN Device IP Settings
IP Address: 192.168.1.254
Subnet Mask: 255.255.255.0
ISP setting in WAN site
PPPoE
DHCP server
DHCP server is enabled.
Start IP Address: 192.168.1.100
IP pool counts: 100
LAN and WAN Port Addresses
The parameters of LAN and WAN ports are pre-set in the factory.
The default values are shown below.
WAN Port
IP address
192.168.1.254
Subnet Mask
255.255.255.0
DHCP server function
Enabled
IP addresses for
distribution to PCs
100 IP addresses continuing from
192.168.1.100 through 192.168.1.199
The PPPoE function is
enabled
to automatically get the WAN
port configuration from the ISP,
but
you
have
to
set
the
username and password first.
Page 18 / 120
VoIP/(802.11g) ADSL2+ Router
Chapter 3: Basic Installation
17
Information from your ISP
Before configuring this device, you have to check with your ISP (Internet Service Provider) what kind of
service is provided such as PPPoE, PPPoA, RFC1483, or IPoA.
Gather the information as illustrated in the following table and keep it for reference.
VPI/VCI, VC-based/LLC-based multiplexing, Username, Password, Service
Name, and Domain Name System (DNS) IP address (it can be automatically
assigned by your ISP when you connect or be set manually).
VPI/VCI, VC-based/LLC-based multiplexing, Username, Password, and
Domain Name System (DNS) IP address (it can be automatically assigned by
your ISP when you connect or be set manually).
VPI/VCI, VC-based/LLC-based multiplexing to use Bridged Mode.
VPI/VCI, VC-based/LLC-based multiplexing, IP address, Subnet mask,
Gateway address, and Domain Name System (DNS) IP address (it is fixed IP
address).
VPI/VCI, VC-based/LLC-based multiplexing, IP address, Subnet mask,
Gateway address, and Domain Name System (DNS) IP address (it is fixed IP
address).
Page 19 / 120
VoIP/(802.11g) ADSL2+ Router
Chapter 3: Basic Installation
18
Configuring with your Web Browser
Open your web browser, enter the IP address of your router, which by default is
192.168.1.254
, and click
Go
”, a user name and password window prompt will appear.
The default username and password
are “admin” and “admin”. (See Figure 3.14)
Figure 3.14: User name & Password Prompt Widonw
Congratulation! You are now successfully logon to the VoIP ADSL2+ Router!
Page 20 / 120
VoIP/(802.11g) ADSL2+ Router
Chapter 4: Configuration
Chapter 4: Configuration
At the configuration homepage, the left navigation pane where bookmarks are provided links you directly
to the desired setup page, including:
Status
(ARP Table, Wireless Association Table(wireless router only), Routing Table, DHCP
Table, Email Status, VoIP Status, Event Log, Error Log, NAT Sessions, Diagnostic and UPnP
Portmap)
Quick Start
Configuration
(LAN, WAN, System, Firewall, VoIP, QoS, Virtual Server, Time Schedule and Advanced)
Save Config to FLASH
Language
(provides user interface in English and French languages)
Please see the relevant sections of this manual for detailed instructions on how to configure the VoIP
ADSL Router.
19

Rate

3.5 / 5 based on 2 votes.

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top