Page 6 / 120
Scroll up to view Page 1 - 5
VoIP/(802.11g) ADSL2+ Router
Chapter 1: Introduction
Dynamic Host Configuration Protocol (DHCP) client and server
In the WAN site, the DHCP client can get an IP address from the Internet Service Provider (ISP)
automatically. In the LAN site, the DHCP server can allocate a range of client IP addresses and
distribute them including IP address, subnet mask as well as DNS IP address to local computers. It
provides an easy way to manage the local IP network.
Static and RIP1/2 Routing
Supports an easy static routing table or RIP1/2 routing protocol to support routing capability.
Simple Network Management Protocol (SNMP)
It is an easy way to remotely manage the router via SNMP.
Web based GUI
Supports web based GUI for configuration and management. It is user-friendly and comes with on-
line help. It also supports remote management capability for remote users to configure and
manage this product.
Firmware Upgradeable
Device can be upgraded to the latest firmware through the WEB based GUI.
Rich management interfaces
Supports flexible management interfaces with local console port, LAN port, and WAN port. Users
can use terminal applications through the console port to configure and manage the device, or
Telnet, WEB GUI, and SNMP through LAN or WAN ports to configure and manage the device.
5
Page 7 / 120
VoIP/(802.11g) ADSL2+ Router
Chapter 2: Installing the router
Chapter 2: Installing the Router
Important note for using this router
Warning
9
Do not use this router in high humidity or high temperatures.
9
Do not use the same power source for this router as other
equipment.
9
Do not open or repair the case yourself.
If this router is too hot,
turn off the power immediately and have it repaired at a qualified
service center.
9
Avoid using this product and all accessories outdoors.
Attention
9
Place this router on a stable surface.
9
Only use the power adapter that comes with the package.
Using
a different voltage rating power adaptor may damage this router.
Package Contents
VoIP/(802.11g) ADSL2+ Router
CD-ROM containing the online manual
RJ-11 ADSL/telephone Cable
Ethernet (CAT-5 LAN) Cable
Console tool
AC-DC power adapter (12VDC, 1A)
A detachable antenna (wireless router only)
Quick Start Guide
6
Page 8 / 120
VoIP/(802.11g) ADSL2+ Router
Chapter 2: Installing the router
The Front LEDs
Meaning
1
PWR
Lit when power is ON.
2
SYS
Lit when the system is ready.
3 – 6
LAN Port
1X
—
4X
(RJ-45 connector)
Lit when connected to an Ethernet device.
Green for 100Mbps; Orange for 10Mbps.
Blinking when data is Transmitted / Received.
8
WLAN
(Wireless router only)
Lit green when the wireless connection is established.
Flashes when sending/receiving data.
9
Phone
(RJ-11 connector)
Lit green when the phone is off-hook.
10
LINE
Lit when the inbound and outbound calls transmitted
through PSTN.
11
VoIP
Lit when SIP registration is OK.
12
ADSL
Lit when successfully connected to an ADSL DSLAM
(“linesync”).
13
PPP / MAIL
Lit steady when there is a PPPoA / PPPoE connection.
Lit and flashed periodically when there is email in the Inbox.
7
Page 9 / 120
VoIP/(802.11g) ADSL2+ Router
Chapter 2: Installing the router
The Rear Ports
3
1
6
5
The Ethernet Port # 4 can be connected to the computer and console. You need
a special console tool which is included in this package to connect the LAN
cable of Port 4 when connecting to a PC’s RS-232 port (9-pin serial port).
8
7
4
2
Meaning
1
Power Switch
Power ON/OFF switch
2
Power
Connect the supplied power adapter to this jack.
3
RESET
After the device is powered on, press it to reset the
device or restore to factory default settings.
0-3 seconds: reset the device
6 seconds above: restore to factory default settings (this
is used when you can not login to the router, e.g. forgot
the password)
4
LAN
1X
—
4X
(RJ-45 connector)
Connect a UTP Ethernet cable (Cat-5 or Cat-5e) to one
of the four LAN ports when connecting to a PC or an
office/home network of 10Mbps or 100Mbps.
5
Phone
(RJ-11 connector)
Connect RJ-11 cable to this port when connecting to an
analog phone set.
6
LINE
Connect RJ-11 cable to this port when connecting to the
telephone wall jack.
7
ADSL
Connect the supplied RJ-11 (“telephone”) cable to this
port when connecting to the ADSL/telephone network.
8
Antenna
(Wireless router only)
Connect the detachable antenna to this port.
8
Page 10 / 120
VoIP/(802.11g) ADSL2+ Router
Chapter 2: Installing the router
Cabling
One of the most common causes of problems is bad cabling or ADSL line(s). Make sure that all
connected devices are turned on. On the front of the product is a bank of LEDs. Verify that the LAN Link
and ADSL line LEDs are lit. If they are not, verify that you are using the proper cables.
Ensure that all other devices connected to the same telephone line as your router (e.g. telephones, fax
machines, analogue modems) have a line filter connected between them and the wall socket (unless
you are using a Central Splitter or Central Filter installed by a qualified and licensed electrician), and
ensure that all line filters are correctly installed and the right way around. Missing line filters or line filters
installed the wrong way around can cause problems with your ADSL connection, including causing
frequent disconnections.
9
19216811.live