Billion BiPAC 7800VDOX Router Manual PDF (Setup & Configuration Guide)

Page 101 / 308 Scroll up to view Page 96 - 100

96

Basic

It let you determine whether to enable Wireless function and set the basic parameters of an AP and

the Virtual APs.

Wireless:

Default setting is set to Enable. If you do not have any wireless devices, check the

checkbox again to unselect.

Hide SSID:

It is function in which transmits its SSID to the air so that when wireless client searches

for a network, router can then be discovered and recognized. Check the checkbox to determine

whether you want to hide SSID.

Clients Isolation:

If you enabled this function, then each of your wireless clients will not be able to

communicate with each other.

Disable WMM Advertise:

Stop the router from ‘advertising’ its Wireless Multimedia (WMM)

functionality, which provides basic quality of service for time-sensitive applications (e.g. VoIP, Video).

Check to disable or enable this function.

Wireless multicast Forwarding (WMF):

check to enable or disable wireless multicast forwarding.

SSID:

The SSID is the unique name of a wireless access point (AP) to be distinguished from another.

For security purpose, change the default wlan-ap-2.4g to a unique ID name to the AP already built-in

to the router’s wireless interface. It is case sensitive and must not excess 32 characters. Make sure

your wireless clients have exactly the SSID as the device, in order to get connected to your network.

Note:

SSID is case sensitive and must not exceed 32 characters.

BSSID:

Basic Set Service Identifier, it is a local managed IEEE MAC address, and is 48 bits value.

Country:

Different countries have different wireless band resources, so you can select the

appropriate Country according to your location.

Max Clients:

enter the number of max clients the wireless network can supports,1-16.

Guest/virtual Access Points:

A “Virtual Access Point” is a logical entity that exists within a physical

Access Point (AP). When a single physical AP supports multiple “Virtual APs”, each Virtual AP

appears to stations (STAs) to be an independent physical AP, even though only a single physical AP

Page 102 / 308

97

is present. For example, multiple Virtual APs might exist within a single physical AP, each advertising

a distinct SSID and capability set. Alternatively, multiple Virtual APs might advertise the same SSID

but a different capability set – allowing access to be provided via Web Portal, WEP, and WPA

simultaneously. Where APs are shared by multiple providers, Virtual APs provide each provider with

separate authentication and accounting data for their users, as well as diagnostic information,

without sharing sensitive management traffic or data between providers. You can enable the virtual

AP.

Here you can enable some Virtual APs according to the request. And the other parameters of virtual

APs are the same to the above.

Click

Apply

to apply your settings.

Page 103 / 308

98

Security

Wireless security prevents unauthorized access or damage to computers using wireless network.

Note

：

The WPS feature will also be unavailable when the security setting is not WPA2 or OPEN. So, if you

manually set the wireless security setting, you should give notice to it, but you can find prompt

indicating configuration.

Manual Setup AP

Select SSID:

select the SSID you want these settings apply to.

Network Authentication



Open

WEP Encryption:

Select to enable or disable WEP Encryption. Here select Enable.

Encryption Strength:

Select the strength, 128-bit or 64-bit.

Current Network Key:

Select the one to be the current network key. Please refer to key 1- 4 below.

Network Key (1- 4):

Enter 13 ASCII characters or 26 hexadecimal digits for 128-bit encryption keys.

Enter 5 ASCII characters or 10 hexadecimal digits for 64-bit encryption keys.

Page 104 / 308

99



Shared

This is similar to network authentication ‘Open’. But here the WEP Encryption must be enabled.



802.1x

RADIUS Server IP Address:

RADIUS( Remote Authentication Dial In User Service), Enter the

IP address of RADIUS authentication server.

RADIUS Server Port:

Enter the port number of RADIUS authentication server here.

RADIUS Key:

Enter the password of RADIUS authentication server.

WEP Encryption:

Select to enable or disable WEP Encryption. Here select Enable.

Current Network Key:

Select the one to be the current network key. Please refer to key 2- 3 below.

Network Key (1- 4):

Enter 13 ASCII characters or 26 hexadecimal digits for 128-bit encryption keys.

Enter 5 ASCII characters or 10 hexadecimal digits for 64-bit encryption keys.

Page 105 / 308

100



WPA

WPA Group ReKey Internal:

The period of renewal time for changing the security key automatically

between wireless client and Access Point (AP). This is in seconds.

RADIUS Server IP Address:

RADIUS( Remote Authentication Dial In User Service), Enter the

IP address of RADIUS authentication server.

RADIUS Server Port:

Enter the port number of RADIUS authentication server here.

RADIUS Key:

Enter the password of RADIUS authentication server.

WPA/WAPI Encryption:

There are two Algorithms, AES (Advanced Encryption Standard) and

TKIP(Temporal Key Integrity Protocol) which help to protect the wireless communication.



WPA-PSK / WPA2-PSK

WPA/WAPI passphrase:

Enter the WPA.WAPI passphrase; you can

click here to display

to view it.

WPA Group ReKey Internal:

The period of renewal time for changing the security key automatically

between wireless client and Access Point (AP). This is in seconds.

WPA/WAPI Encryption:

There are two Algorithms, AES (Advanced Encryption Standard) and

TKIP(Temporal Key Integrity Protocol) which help to protect the wireless communication.

Rate

Popular Billion Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share