1. Home
    2. /
  2. Manuals
    3. /
  3. Allied-Telesis
    4. /
  4. AT-iMG624A
    5. /
  5. 183
Page 911 / 998 Scroll up to view Page 906 - 910
PPPoA command reference
PPPoA
8-141
iMG/RG Software Reference Manual (ADSL Port)
Options
The following table gives the range of values for each option that can be specified with
this command and a default value (if applicable).
Example
--> pppoa set transport pppoa1 remoteip 192.168.103.2
See also
PPPOA SHOW TRANSPORT
PPPOA LIST TRANSPORTS
PPPOA SET TRANSPORT LOCALIP
8.8.1.1.35 PPPOA SET TRANSPORT ROUTEMASK
Syntax
PPPOA SET TRANSPORT {<name>|<number>} ROUTEMASK <mask>
Description
This command sets the subnet mask used by the route that is created when a PPP link
comes up. If it is set to 0.0.0.0, the subnet mask is determined by the IP address of the
remote end of the link. The class of the IP address is obtained during IPCP (
Internet Pro-
tocol Control Protocol
) negotiation.
Options
The following table gives the range of values for each option that can be specified with
this command and a default value (if applicable).
Option
Description
Default Value
name
An existing PPPoA transport. To display transport
names, use the
PPPOA LIST TRANSPORTS
com-
mand.
N/A
number
An existing PPPoA transport. To display transport num-
bers, use the
PPPOA LIST TRANSPORTS
com-
mand.
N/A
ip-address
The ip address of the local ‘server-end’ of an interface
displayed in the following format: 111.222.254.4
0.0.0.0
Option
Description
Default Value
name
An existing PPPoA transport. To display transport
names, use the
PPPOA LIST TRANSPORTS
com-
mand.
N/A
number
An existing PPPoA transport. To display transport num-
bers, use the
PPPOA LIST TRANSPORTS
com-
mand.
N/A
Page 912 / 998
PPPoA
PPPoA command reference
iMG/RG Software Reference Manual (ADSL Port)
8-142
Example
--> pppoa set transport pppoa1 routemask 0.0.0.0
See also
PPPOA SHOW TRANSPORT
PPPOA LIST TRANSPORTS
8.8.1.1.36 PPPOA SET TRANSPORT SCR
Syntax
PPPOA SET TRANSPORT {<name>|<number>} SCR <sustainable cell
rate>
Description
This command applies to existing PVC transports - it does not apply
to SVC transports.
This command is only valid if you set VBR or VBR RT as the QoS Class using the pppoa
set transport qosclass command.
The following table gives the range of values for each option that can be specified with
this command and a default value (if applicable).
Example
--> pppoa set transport pppoa2 scr 25000
See also
PPPOA SET TRANSPORT QOSCLASS
8.8.1.1.37 PPPOA SET TRANSPORT SPECIFICROUTE
Syntax
PPPOA SET TRANSPORT {<name>|<number>} SPECIFICROUTE {ENABLED
| DISABLED}
Description
This command specifies whether the route created when a PPP link comes up is a spe-
cific or default route. If set to enabled, the route created will only apply to packets for
mask
The subnet mask that is used for the route that is cre-
ated when a PPP link comes up. 0.0.0.0
0.0.0.0
Option
Description
Default Value
name
An existing PPPoA transport. To display transport
names, use the
PPPOA LIST TRANSPORTS
command.
N/A
number
An existing PPPoA transport. To display transport
numbers, use the
PPPOA LIST TRANSPORTS
command.
N/A
sustainable cell rate
Sustainable Cell Rate; the average cell rate for a VBR
or VBR RT connection. The SCR can be any positive
value that is less than the PortSpeed and the PCR for
the channel.
0
Option
Description
Default Value
Page 913 / 998
PPPoA command reference
PPPoA
8-143
iMG/RG Software Reference Manual (ADSL Port)
the subnet at the remote end of the PPP link. The address of this subnet is obtained dur-
ing IPCP negotiation.
Note:
This command is only valid if the
PPPOA SET TRANSPORT CREATEROUTE
command is set to
enabled
. If the
CREATEROUTE COMMAND
is set to
disabled
, no route is created and therefore the
PPPOA SET TRANSPORT SPECIFICROUTE
command is ignored.
The mask for the route is calculated from the class of the remote subnet unless an alter-
native has been specified using the
PPPOA SET TRANSPORT ROUTEMASK
command.
If specificroute is set to disabled, a default route to the subnet at the remote end of the
PPP link is created.
Options
The following table gives the range of values for each option that can be specified with
this command and a default value (if applicable).
Example
--> pppoa set transport pppoa1 specificroute disabled
See also
PPPOA SET TRANSPORT ROUTEMASK
PPPOA SET TRANSPORT CREATEROUTE
PPPOA LIST TRANSPORTS
PPPOA SHOW TRANSPORT
8.8.1.1.38 PPPOA SET TRANSPORT SUBNETMASK
Syntax
PPPOA SET TRANSPORT {<name>|<number>} SUBNETMASK <mask>
Description
This command sets the subnet mask used for the local IP interface connected to the PPP
transport. If the value 0.0.0.0 is supplied, the netmask will be calculated from the class of
the IP address obtained during IPCP negotiation.
Option
Description
Default Value
name
An existing PPPoA transport. To display transport
names, use the
PPPOA LIST TRANSPORTS
com-
mand.
N/A
number
An existing PPPoA transport. To display transport num-
bers, use the
PPPOA LIST TRANSPORTS
com-
mand.
N/A
enabled
Allows the created route to apply to packets for the
subnet at the remote end of the PPP link.
disabled
disabled
A default route to the subnet at the remote end of the
PPP link is created.
Page 914 / 998
PPPoA
PPPoA command reference
iMG/RG Software Reference Manual (ADSL Port)
8-144
Options
The following table gives the range of values for each option that can be specified with
this command and a default value (if applicable).
Example
--> pppoa set transport pppoa1 subnetmask 255.255.255.0
See also
PPPOA LIST TRANSPORTS
8.8.1.1.39 PPPOA SET TRANSPORT THEYLOGIN
Syntax
PPPOA SET TRANSPORT {<name>|<number>} THEYLOGIN
{NONE|PAP|CHAP}
Description
This command sets the authentication method that remote PPP clients must use to dialin
to the server. If authentication is used, clients must use the specified authentication
method and provide the username set using the
SYSTEM ADD USER
command.
This command is only valid if the user has maydialin set using the
SYSTEM SET LOGIN
MAYDIALIN
command.
Options
The following table gives the range of values for each option that can be specified with
this command and a default value (if applicable).
Option
Description
Default Value
name
An existing PPPoA transport. To display transport names, use
the
PPPOA LIST TRANSPORTS
command.
N/A
number
An existing PPPoA transport. To display transport numbers, use
the
PPPOA LIST TRANSPORTS
command.
N/A
mask
The subnet mask used by the local IP interface connected to
the PPP transport.
0.0.0.0
Option
Description
Default Value
name
An existing PPPoA transport. To display transport names, use
the
PPPOA LIST TRANSPORTS
command.
N/A
number
An existing PPPoA transport. To display transport numbers, use
the
PPPOA LIST TRANSPORTS
command.
N/A
none
No authentication method is set.
None
pap
Password Authentication Protocol
; the server sends an
authentication request to the remote user dialing in. PAP passes
the un-encrypted username and password and identifies the
remote end.
Page 915 / 998
PPPoA command reference
PPPoA
8-145
iMG/RG Software Reference Manual (ADSL Port)
Example
--> pppoa set transport pppoa2 theylogin pap
See also
PPPOA LIST TRANSPORTS
PPPOA SHOW TRANSPORT
SYSTEM ADD USER
SYSTEM SET USER MAYDIALIN
8.8.1.1.40 PPPOA SET TRANSPORT USERNAME
Syntax
PPPOA SET TRANSPORT {<name>|<number>} USERNAME <username>
Description
This command sets a (dial-out) username on a named transport. The username is
required when PPP negotiation takes place and is supplied to the remote PPP server for
authentication.
Options
The following table gives the range of values for each option that can be specified with
this command and a default value (if applicable).
Example
--> pppoa set transport pppoa2 username jsmith
See also
PPPOA SET TRANSPORT PASSWORD
8.8.1.1.41 PPPOA SET TRANSPORT VCI
Syntax
PPPOA SET TRANSPORT {<name>|<number>} VCI <vci>
chap
Challenge Handshake Authentication Protocol
; the
server sends an authentication request to the remote user dial-
ing in. PAP passes the encrypted username and password and
identifies the remote end.
Option
Description
Default Value
name
An existing PPPoA transport. To display transport names, use
the
PPPOA LIST TRANSPORTS
command.
N/A
number
An existing PPPoA transport. To display transport numbers,
use the
PPPOA LIST TRANSPORTS
command.
N/A
username
A name that identifies a user and, together with the dialout
password, enables a user to login to the remote end. The
PPP server will require the username when the user wants to
login remotely. It can be made up of one or more characters
and/or digits. To display the username, use the
PPPOA
SHOW TRANSPORT
command.
N/A
Option
Description
Default Value

Rate

4 / 5 based on 3 votes.

Popular Allied-Telesis Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top