1. Home
    2. /
  2. Manuals
    3. /
  3. Allied-Telesis
    4. /
  4. AT-iMG624A
    5. /
  5. 181
Page 901 / 998 Scroll up to view Page 896 - 900
PPPoA command reference
PPPoA
8-131
iMG/RG Software Reference Manual (ADSL Port)
received, the PPP connection is torn down. This functionality is also known as ‘keep-
alive’.
If you do not want to send LCP echo frames, specify zero (0) in the <interval> attribute.
Options
The following table gives the range of values for each option that can be specified with
this command and a default value (if applicable).
Example
--> pppoa set transport pppoa2 lcpechoevery 0
See also
PPPOA SHOW TRANSPORT
PPPOA LIST TRANSPORTS
8.8.1.1.21 PPPOA SET TRANSPORT LCPMAXCONF
Syntax
PPPOA SET TRANSPORT
{<name>|<number>}
LCPMAXCONF
<lcp max con-
figure>
Description
This command sets the
Link Control Protocol
(LCP) maximum configure number for an
existing PPPoA transport.
Options
The following table gives the range of values for each option that can be specified with
this command and a default value (if applicable).
Option
Description
Default Value
name
An existing PPPoA transport. To display transport names,
use the
PPPOA LIST TRANSPORTS
command.
N/A
number
An existing PPPoA transport. To display transport num-
bers, use the
PPPOA LIST TRANSPORTS
com-
mand.
N/A
interval
The length of time (in seconds) between LCP echo
request frames being sent. If you do not want echo
request frames to be sent, specify ‘0’ as the interval.
10 seconds
Option
Description
Default Value
name
An existing PPPoA transport. To display transport
names, use the
PPPOA LIST TRANSPORTS
command.
N/A
number
An existing PPPoA transport. To display transport
numbers, use the
PPPOA LIST TRANSPORTS
command.
N/A
Page 902 / 998
PPPoA
PPPoA command reference
iMG/RG Software Reference Manual (ADSL Port)
8-132
Example
--> pppoa set transport pppoa1 lcpmaxconf 20
See also
PPPOA SHOW TRANSPORT
PPPOA LIST TRANSPORTS
8.8.1.1.22 PPPOA SET TRANSPORT LCPMAXFAIL
Syntax
PPPOA SET TRANSPORT
{<name>|<number>}
LCPMAXFAIL
<lcp max
fail>
Description
This command sets the
Link Control Protocol
(LCP) maximum fail number for an exist-
ing PPPoA transport.
Options
The following table gives the range of values for each option that can be specified with
this command and a default value (if applicable).
Example
--> pppoa set transport pppoa1 lcpmaxfail 20
See also
PPPOA SHOW TRANSPORT
PPPOA LIST TRANSPORTS
8.8.1.1.23 PPPOA SET TRANSPORT LCPMAXTERM
Syntax
PPPOA SET TRANSPORT
{<name>|<number
>} LCPMAXTERM
<lcp max termi-
nate>
lcp max configure
Link Control Protocol
; the maximum number of
configures that can be transmitted without reply
before assuming that the destination address is unable
to respond. The LCPmaxconf can be any positive
value.
10
Option
Description
Default Value
name
An existing PPPoA transport. To display transport names,
use the
PPPOA LIST TRANSPORTS
command.
N/A
number
An existing PPPoA transport. To display transport num-
bers, use the
PPPOA LIST TRANSPORTS
com-
mand.
N/A
lcp max fail
Link Control Protocol
; the maximum number of con-
secutive negative acknowledgements (indicating that the
information received contains errors) that can be trans-
mitted before assuming that parameter negotiation is not
converging. The LCPmaxfail can be any positive value.
5
Option
Description
Default Value
Page 903 / 998
PPPoA command reference
PPPoA
8-133
iMG/RG Software Reference Manual (ADSL Port)
Description
This command sets the
Link Control Protocol
(LCP) maximum terminate number for an
existing PPPoA transport.
Options
The following table gives the range of values for each option that can be specified with
this command and a default value (if applicable).
Example
--> pppoa set transport pppoa1 lcpmaxterm 20
See also
PPPOA SHOW TRANSPORT
PPPOA LIST TRANSPORTS
8.8.1.1.24 PPPOA SET TRANSPORT LOCALIP
Syntax
PPPOA SET TRANSPORT {<name>|<number>} LOCALIP <ip-address>
Description
This command is only applicable to dialin SVC or PVC transports that provide the server-
end of a connection. The command tells the PPP process the local IP address to be asso-
ciated with the client-end of an interface. This allows remote users to have dialin access
via the channel(s) that the interface is attached to.
Options
The following table gives the range of values for each option that can be specified with
this command and a default value (if applicable).
Option
Description
Default Value
name
An existing PPPoA transport. To display transport names, use
the
PPPOA LIST TRANSPORTS
command.
N/A
number
An existing PPPoA transport. To display transport numbers,
use the
PPPOA LIST TRANSPORTS
command.
N/A
lcp max term
Link Control Protocol
; the maximum number of consecu-
tive Terminate Requests that will be sent without reply
before assuming that the destination address is unable to
respond. The LCPfailterm can be any positive value.
2
Option
Description
Default Value
name
An existing PPPoA transport. To display transport
names, use
THE PPPOA LIST TRANSPORTS
command.
N/A
number
An existing PPPoA transport. To display transport num-
bers, use the
PPPOA LIST TRANSPORTS
com-
mand.
N/A
Page 904 / 998
PPPoA
PPPoA command reference
iMG/RG Software Reference Manual (ADSL Port)
8-134
Example
--> pppoa set transport pppoa1 localip 192.168.103.2
See also
PPPOA SHOW TRANSPORT
PPPOA LIST TRANSPORTS
PPPOA SET TRANSPORT REMOTEIP
8.8.1.1.25 PPPOA SET TRANSPORT MBS
Syntax
PPPOA SET TRANSPORT {<name>|<number>} MBS <max burst size>
Description
This command applies to existing PVC transports - it does not apply
to SVC transports.
It sets the
Maximum Burst Size
(MBS) for the PPPoA transport.
This command is only valid if you set VBR or VBR RT as the QoS Class using the pppoa
set transport quosclass command.
Example
--> pppoa set transport pppoa3 mbs 10
See also
PPPOA SET TRANSPORT BT
PPPOA SET TRANSPORT QOSCLASS
8.8.1.1.26 PPPOA SET TRANSPORT MCR
Syntax
PPPOA SET TRANSPORT {<name>|<number>} MCR <min cell rate>
Description
This command applies to existing PVC transports - it does not apply
to SVC transports.
This command sets the minimum cell rate for an existing PPPoA transport.
ip-address
The ip address of the local ‘client-end’ of an interface
displayed in the following format: 111.222.254.4
0.0.0.0
Option
Description
Default Value
name
An existing PPPoA transport. To display transport
names, use the
PPPOA LIST TRANSPORTS
com-
mand.
N/A
number
An existing PPPoA transport. To display transport num-
bers, use the
PPPOA LIST TRANSPORTS
com-
mand.
N/A
maximum burst
size
Controls the maximum burst size for VBR (
Variable
Bit Rate
) and VBR RT (
VBR Real Time
) channels.
This value overrides an existing BT value (if set). The
MBS can be any value between 0 and 100.
0
Option
Description
Default Value
Page 905 / 998
PPPoA command reference
PPPoA
8-135
iMG/RG Software Reference Manual (ADSL Port)
Options
The following table gives the range of values for each option that can be specified with
this command and a default value (if applicable).
Example
--> pppoa set transport pppoa2 mcr 0
See also
PPPOA SET TRANSPORT PCR
8.8.1.1.27 PPPOA SET TRANSPORT PASSWORD
Syntax
PPPOA SET TRANSPORT {<name>|<number>} PASSWORD <password>
Description
This command sets a dial-out password on a named transport. The password is required
when PPP negotiation takes place and is supplied to the remote PPP server for authenti-
cation.
Options
The following table gives the range of values for each option that can be specified with
this command and a default value (if applicable).
Example
--> pppoa set transport pppoa2 password mercury
Option
Description
Default Value
name
An existing PPPoA transport. To display transport
names, use the
PPPOA LIST TRANSPORTS
command.
N/A
number
An existing PPPoA transport. To display transport
numbers, use the
PPPOA LIST TRANSPORTS
command.
N/A
minimum cell rate
Determines the minimum rate at which ATM cells can
be sent along the PPPoA transport.
0
Option
Description
Default Value
name
An existing PPPoA transport. To display transport names, use
the
PPPOA LIST TRANSPORTS
command.
N/A
number
An existing PPPoA transport. To display transport numbers, use
the
PPPOA LIST TRANSPORTS
command.
N/A
password
An arbitrary word that acts as a dialout password enabling you
to login to the remote end. The PPP server will require the
password when you want to login remotely. It can be made up
of one or more characters and/or digits. To display the pass-
word, use the
PPPOA SHOW TRANSPORT
command.
N/A

Rate

4 / 5 based on 3 votes.

Popular Allied-Telesis Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top