1. Home
    2. /
  2. Manuals
    3. /
  3. Allied-Telesis
    4. /
  4. AT-iMG624A
    5. /
  5. 182
Page 906 / 998 Scroll up to view Page 901 - 905
PPPoA
PPPoA command reference
iMG/RG Software Reference Manual (ADSL Port)
8-136
See also
PPPOA LIST TRANSPORTS
PPPOA SHOW TRANSPORT
PPPOA SET TRANSPORT USERNAME
8.8.1.1.28 PPPOA SET TRANSPORT PCR
Syntax
PPPOA SET TRANSPORT {<name>|<number>} PCR <peak cell rate>
Description
This command applies to existing PVC transports - it does not apply to SVC transports.
This command sets the
Peak Cell Rate
(PCR) for an existing PPPoA transport.
Options
The following table gives the range of values for each option that can be specified with
this command and a default value (if applicable).
Example
--> pppoa set transport pppoa2 pcr 50000
See also
PPPOA SET TRANSPORT MCR
8.8.1.1.29 PPPOA SET TRANSPORT PORT
Syntax
PPPOA SET TRANSPORT {<name>|<number>} PORT <port>
Description
This command applies to existing PVC transports - it does not apply
to SVC transports.
This command sets the port that an existing transport uses to transport PPPoA data.
The port/VPI/VCI combination must be unique for each transport.
Options
The following table gives the range of values for each option that can be specified with
this command and a default value (if applicable).
Option
Description
Default Value
name
An existing PPPoA transport. To display transport names, use
the
PPPOA LIST TRANSPORTS
command.
N/A
number
An existing PPPoA transport. To display transport numbers,
use the
PPPOA LIST TRANSPORTS
command.
N/A
peak cell rate
Determines the maximum rate at which ATM cells can be
sent along the PPPoA transport. The PCR can be any value
from 0 up to the maximum PortSpeed parameter set when
the port was created (using the initbun file in
FlashFS
or
the CLI command
PORT LIST
).
0
Option
Description
Default Value
name
An existing PPPoA transport. To display transport names,
use the
PPPOA LIST TRANSPORTS
command.
N/A
Page 907 / 998
PPPoA command reference
PPPoA
8-137
iMG/RG Software Reference Manual (ADSL Port)
Example
--> pppoa set transport pppoa4 port a1
See also
pppoa list transports
port list
8.8.1.1.30 PPPOA SET TRANSPORT PRILEVELS
Syntax
PPPOA SET TRANSPORT {<name>|<number>} PRILEVELS <prilevels>
Description
This command enables support for multiple packet priority levels on the same ATM VC.
Two prilevel values are supported:
•
There are no multiple priority levels enabled so the feature is disabled.
•
Packets with different priorities set (such as best effort and high priority traffic) are
prioritized on the same ATM VC.
Options
The following table gives the range of values for each option that can be specified with
this command and a default value (if applicable).
Example
--> pppoa set transport myrfc prilevels 2
See also
PPPOA SHOW TRANSPORT
8.8.1.1.31 PPPOA SET TRANSPORT PVC
Syntax
PPPOA SET TRANSPORT {<name>|<number>} PVC <port> <vpi> <vci>
Description
This command sets the PVC information for an existing PPPoA transport PVC. The PVC
uses the interface that was specified when the transport was created.
number
An existing PPPoA transport. To display transport num-
bers, use the
PPPOA LIST TRANSPORTS
com-
mand.
N/A
port
The system port that is used to transport ATM data.
N/A
Option
Description
Default Value
name
An existing PPPoA transport. To display transport names, use
the
PPPOA LIST TRANSPORTS
command.
N/A
number
An existing PPPoA transport. To display transport numbers,
use the
PPPOA LIST TRANSPORTS
command.
N/A
prilevels
The number of priority levels available on an ATM transport.
1
Option
Description
Default Value
Page 908 / 998
PPPoA
PPPoA command reference
iMG/RG Software Reference Manual (ADSL Port)
8-138
The command allows you to specify the following PVC information:
•
The ATM port that will transport data
•
VPI (Virtual Path Identifier)
•
VCI (Virtual Circuit Identifier)
The port/VPI/VCI combination must be unique for each transport.
Options
The following table gives the range of values for each option that can be specified with
this command and a default value (if applicable).
Example
--> pppoa set transport pppoa2 pvc a1 0 800
See also
PPPOA LIST TRANSPORTS
PPPOA SET TRANSPORT DIALIN PVC
PPPOA SET TRANSPORT DIALOUT PVC
PORT LIST
8.8.1.1.32 PPPOA SET TRANSPORT QOSCLASS
Syntax
PPPOA SET TRANSPORT {<name>|<number>} QOSCLASS
{UBR|CBR|VBR|VBRRT|ABR|QFC}
Description
This command applies to existing PVC transports - it does not apply to SVC transports.
It sets the quality of service class for the transport.
Options
The following table gives the range of values for each option that can be specified with
this command and a default value (if applicable).
Option
Description
Default Value
name
An existing PPPoA transport. To display transport names, use
the
PPPOA LIST TRANSPORTS
command.
N/A
number
An existing PPPoA transport. To display transport numbers,
use the
PPPOA LIST TRANSPORTS
command.
N/A
port
The system port that is used to transport ATM data.
N/A
vpi
A field in the ATM header. The VPI is used to identify the vir-
tual path that a circuit belongs to. The VPI can be any value
between 0 and 4095.
N/A
vci
Part of the ATM header. The VCI is a tag that identifies which
channel a cell will travel over. The VCI can be any value
between 1 and 65535.
N/A
Page 909 / 998
PPPoA command reference
PPPoA
8-139
iMG/RG Software Reference Manual (ADSL Port)
Example
--> pppoa set transport pppoa3 qosclass abr
See also
PPPOA SHOW TRANSPORT
PPPOA SET TRANSPORT QOSCLASS
8.8.1.1.33 PPPOA SET TRANSPORT REMOTEDNS
Syntax
PPPOA SET TRANSPORT {<name>|<number>} REMOTEDNS <ipaddress>
[<ipaddress2>]
Description
This command is a PPP server function.
This command sets the primary and secondary local DNS server addresses that will be
given to a remote PPP peer when the peer requests a primary or secondary DNS server
IP address using IPCP. Setting the secondary IP address is optional.
Option
Description
Default Value
name
An existing PPPoA transport. To display transport names,
use the
PPPOA LIST TRANSPORTS
command.
N/A
number
An existing PPPoA transport. To display transport num-
bers, use the
PPPOA LIST TRANSPORTS
com-
mand.
N/A
ubr
Unspecified Bit Rate; non-constant and unpredictable data
transport rate. PCR (
Peak Cell Rate
) is the average and
maximum speed of transmission.
UBR
cbr
Constant Bit Rate
; constant demand and predictable
data transport rate. PCR is the average and maximum
speed of transmission.
vbr
Variable Bit Rate
; non-constant but predictable data
transport rate that uses
Non-Real-Time
(NRT). You can
specify the PCR, SCR, BT and MBS for VBR traffic.
vbrrt
Variable Bit Rate Real-Time
; non-constant but predict-
able data transport rate that uses
Real-Time
(RT). You
can specify the PCR, SCR, BT and MBS for VBRRT traffic.
abr
Available Bit Rate
; non-constant and unpredictable data
transport rate that provides ATM-layer feedback and flow
control.
qfc
QFC: ATM flow control protocol that supports ABR.
Page 910 / 998
PPPoA
PPPoA command reference
iMG/RG Software Reference Manual (ADSL Port)
8-140
If you want to delete an IP address, set the IP address to 0.0.0.0.
Options
The following table gives the range of values for each option that can be specified with
this command and a default value (if applicable).
ExamplesExample 1 - setting a primary address
--> pppoa set transport pppoa1 remotedns 192.168.102.3
Example 2 - setting primary and secondary addresses
To set primary and secondary addresses, use this command syntax:
--> pppoa set transport pppoa1 remotedns 192.168.102.3 192.168.105.1
Example 3 - deleting an address
To delete an address, set it to 0.0.0.0. The example below deletes the secondary address
that was set in Example Two:
--> pppoa set transport pppoa1 remotedns 192.168.102.3 0.0.0.0
See also
PPPOA SET TRANSPORT GIVEDNS CLIENT ENABLED|DISABLED
PPPOA SET TRANSPORT GIVEDNS RELAY ENABLED|DISABLED
PPPOA SET TRANSPORT DISCOVERDNS PRIMARY
PPPOA SET TRANSPORT DISCOVERDNS SECONDARY
8.8.1.1.34 PPPOA SET TRANSPORT REMOTEIP
Syntax
PPPOA SET TRANSPORT {<name>|<number>} REMOTEIP <ip-address>
Description
This command sets the IP address supplied to the remote end of the PPP connection
during negotiation. This is particularly important for PPP dialin transports.
Option
Description
Default Value
name
An existing pppoa transport. To display transport
names, use the
PPPOA LIST TRANSPORTS
com-
mand.
N/A
number
An existing pppoa transport. To display transport num-
bers, use
THE PPPOA LIST TRANSPORTS
command.
N/A
ipaddress
The ip address of the primary local DNS server dis-
played in the following format: 192.168.102.3
0.0.0.0
(no primary
address set)
ipaddress2
The ip address of the secondary local DNS server dis-
played in the following format: 192.168.102.3
0.0.0.0
(no secondary
address set)

Rate

4 / 5 based on 3 votes.

Popular Allied-Telesis Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top