Page 31 / 56
Scroll up to view Page 26 - 30
Confidential and Proprietary Information of ZTE CORPORATION 31
AES
Select AES as the encryption type.
AUTO
Both TKIP and AES are selected as the encryption type.
•
Pass phrase
: Enter the password manually.
If the security mode is
SHARED,
the bottom part of the configuration page displays parameters as shown
below:
WEP
Keys
: At most four keys can be set in the WEP key fields. Choose the primary key index. The
primary key is the only key in use at a given time. Whatever keys you enter for an access point, you
must also enter the same keys for the client adapter in the same order. In other words, WEP key 1 on the
AP must match WEP key 1 on the client adapter; and WEP key 2 the same. A WEP can be in HEX form
with either 10 or 26 hexadecimal digits (0~9,a~f and A~F) and in ASCII form with either 5or 13 ASCII
code.
If the security mode is
OPEN
, the bottom part of the configuration page displays WPA parameters.
Page 32 / 56
32 Confidential and Proprietary Information of ZTE CORPORATION
•
Encrypt Type
: There are two encrypt types:
WEP
and
No ENCRYPTION
.
WPS
Select
Settings > Wi-Fi Settings > WPS
,
•
WPS mode
: Choose the desired mode.
AP PIN
：
AP PIN will be displayed when WPS is activated.
Page 33 / 56
Confidential and Proprietary Information of ZTE CORPORATION 33
Client PIN:
Enter the client PIN. As required, the PIN should be 8 digits.
PBC
：
1. Select
PBC
mode in the Client WPS UI;
2. Select
PBC
mode in the WPS page of the 4G Mobile Hotspot and submit; H
3. Once the WPS is enabled, please press the "
next
" button on the Client WPS UI. After a few seconds the
client can access the WLAN, and the result will be shown in the Client WPS UI.
Click
Apply
to confirm your configuration.
Usage of WPS
WPS of your 4G Mobile Hotspot is disabled by default. Before using, you need to enable it in the
Page 34 / 56
34 Confidential and Proprietary Information of ZTE CORPORATION
WebGUI configuration page (
Settings > Wi-Fi Settings > WPS
) or by pressing the
WPS
button at right
side of the device.
If your client device supports WPS, you will not need to input the password manually after WPS has been
available. Please follow the steps below:
1. Start up your 4G Mobile Hotspot.
2. Launch the client device connected to your 4G Mobile Hotspot.
3. Enable the WPS function of your 4G Mobile Hotspot.
4. Enable the WPS function of the connecting client.
Notes:
For detailed operations about the client, please refer to the
client’
s User Guide.
Settings > Firewall
You may setup firewall rules to protect your network from virus, worm and malicious activity on the
Internet.
Notes:
You can set maximum 10 filtering items for
MAC/IP/Port Filtering
and
Port Forwarding
.
MAC/IP/Port Filtering
Select
Settings > Firewall > Mac/IP/Port Filtering
,
If you select
Enable
, the filter settings will appear:
Page 35 / 56
Confidential and Proprietary Information of ZTE CORPORATION 35
•
Default Policy
: Set how to handle the packet if none of the rules matches.
•
MAC address
: Set the MAC address that will be filtered.
•
Dest. IP Address
: Set the destination IP address that will be filtered.
•
Source IP Address
: Set the source IP address that will be filtered.
•
Protocol
: Set which protocol will be used for filtering.
•
Dest. Port Range
: Set the destination port numbers that will be filtered
•
Source Port Range
: Set the source port numbers that will be filtered.
•
Action
: Set how to handle the packet if it matches the rule.
•
Comment
: Type comment for the filter settings.
Notes:
Filtering rules are matched one by one. Once a provision is met, it will not continue to match the rules
listed below.
Click
Apply
to confirm your configuration.
Click
Delete
to remove the rule which you selected.
Click
Reset
to restore default values.
To add a new rule:
1. Select
Enable
in the
Basic Settings
area.
2. Click
Apply
.
19216811.live