6 Confidential and Proprietary Information of ZTE CORPORATION

Resetting the 4G Mobile Hotspot

•

Press and hold the

WPS

and

Power

buttons simultaneously until the LCD turns off; then release the

buttons and the 4G Mobile Hotspot will restart automatically and restore to the factory default settings.

The 4G Mobile Hotspot

will display ―Restarting…‖

which indicates a successful reset to factory

defaults. You can also reset the 4G Mobile Hotspot settings through the web admin page.

•

is a trademark of SD Card Association.

LCD Screen Indicator

4G Mobile Hotspot Icon Indicators

Icon

Indication

Network signal strength. The antenna to the far left counts as one bar. More bars

means better coverage.

4G

4G network type, which means the device is being connected to a 4G network.

E

Edge network type, which means the device is being connected to an Edge network.

G

GPRS network type, which means the device is being connected to a GPRS network.

Network signal not detected.

5

New message received, and the number beside the icon indicates the number of the

unread messages.

Wi-Fi is not being broadcast.

A short press of

the ―WPS‖ button

will turn on the

Wi-Fi radio.

Wi-Fi is being broadcast, and the number of the connected users is indicated to the

right of the Wi-Fi antenna (maximum of 5 total).

Battery power indication.

The battery indicator will flash when the battery is

almost drained.

Hardware Installation

About SIM Card

Avoid handling the

SIM

card unnecessarily. Hold the card by the edges to prevent static damage. Keep

the SIM card away from electrical and magnetic appliances.

If you cannot get T-Mobile wireless service, please ensure:

1.Your T-Mobile service has been activated and you have a mobile phone number.

2.You are in an area with T-Mobile network coverage

Confidential and Proprietary Information of ZTE CORPORATION 7

3.

Your T-Mobile SIM Card is properly inserted in the SIM card slot.

Inserting SIM Card and Battery

Warning:

Power off the 4G Mobile Hotspot and remove the external power adapter before removing or inserting

the SIM card. Otherwise, the 4G Mobile Hotspot or SIM card may be damaged.

1. Open the battery cover, located on the bottom of the 4G Mobile Hotspot.

2. Remove the battery.

3. Insert SIM Card into the designated slot.

3. Insert the battery as shown with the contacts located against the metal springs.

4. Line the battery cover up correctly and press gently to close the case.

8 Confidential and Proprietary Information of ZTE CORPORATION

Inserting microSD Card

1. Pull the microSD cover out of the card slot.

Notes:

Do not pull the MicroSD cover too hard, as it could break with excessive force.

2. Insert the microSD card into the microSD slot. The following picture shows the front of the 4G Mobile

Hotspot

and how to correctly insert the microSD. You will hear and feel a click when the microSD card

locks in place.

3. Close the microSD cover.

Switching On/Off Your 4G Mobile Hotspot

Press and hold the

Power

button for 3 seconds to turn on/off the 4G Mobile Hotspot.

Notes:

•

The 4G Mobile Hotspot is powered on when the LCD lights up

and shows ―T

-

Mobile‖

.

Charging Your 4G Mobile Hotspot

Notes:

•

You can charge your 4G Mobile Hotspot by using the USB cable provided with your device.

1. Insert the charger cable carefully into your 4G Mobile Hotspot with the plug arrow facing the bottom of

the device.

2. The plug only fits one way. Do not use excessive force to insert the plug.

Confidential and Proprietary Information of ZTE CORPORATION 9

Confidential and Proprietary Information of ZTE CORPORATION 10

C h a p t e r

2

Working Mode

Your 4G Mobile Hotspot supports two working modes: USB mode and Wi-Fi mode. This document uses

PC or laptop connectivity for examples of connecting 4G Mobile Hotspot.

USB Mode

Connect the 4G Mobile Hotspot to your PC or laptop via the included USB cable, and then power on your

4G Mobile Hotspot.

Software Installation for Windows XP

When you connect your 4G Mobile Hotspot to Windows PC or laptop for the first time, the system will

automatically detect and recognize the new hardware and display the new icon

in the desktop status

bar, indicating that the PC or laptop and the 4G Mobile Hotspot have been connected properly. After a

few seconds, the following installation interface will be shown if the laptop and desktop PC supports

automatic installation.

Notes: