Page 11 / 39
Scroll up to view Page 6 - 10
7
C h a p t e r
3
Voice
Making a Call
You have two ways to make a call:
•
Through (U)SIM card.
•
Through PSTN.
To make a call:
1. Pick up the handset.
2. Key in the telephone number.
3. You can either press
#
key on the telephone to send the call, or wait 4
～
8 seconds for the call to be
connected automatically.
4. Call will be connected.
Notes:
If there is no 3G indication, the RF signal is unavailable. Change the location of the router and make sure
nothing is blocking it.
Making a Trunk Call
If you are making a trunk call, add the area code as normal.
E.g. 03 9612 3456
Making an International Call
If you are making an international call, key in the international access code followed by the country code,
area code and number.
E.g. 00 11 64 12 345678
Answering a Call
When the phone rings, pick up the handset to answer it. If the telephone has hands-free function you also
can answer the call by pressing the
Hands-free
button. Press the
Hands-free
button again to end the call.
Page 12 / 39
8
C h a p t e r
4
Internet Access
The router does not require any drivers, and it supports all operating systems with Ethernet LAN
capability, such as Windows 2000, XP, Vista, MAC OS X and Linux. The router supports two computers
surfing on internet using Ethernet cable at the same time.
Note: All the parameter settings in this chapter are just for your reference. Please contact your service
provider for detail.
Preparation
Establishing a connection between your device and the client
Via RJ45 Ethernet cable
1.Connect your device and the client with the RJ45 Ethernet cable.
2.Power on your device.
The connection between your device and the client will be established successfully a moment later.
Via Wi-Fi
1. Power on your device directly. It will take 1~2 minutes to initialize, and then Wi-Fi LED is blinking.
2. Use your normal Wi-Fi application on the client to search the available wireless network.
Notes: You need to check your Wireless Network Connection. Set the client to obtain an
IP address automatically in the Internet protocol (TCP/IP) properties, and the client will get
an IP address like
”
192.168.0.100
”
.
3. Select the SSID of your device, and then click
Connect
.
Page 13 / 39
9
Notes
:
There will be a pop-up window to require the password. Please check the label on the battery
compartment of your device to gain the SSID and preset password information.
4. Wait a moment, the connection between your device and the client will be established
successfully.
Accessing the Internet
Before accessing the internet, make sure;
1. Switch on the device.
2. Establish a connection between your device and the client.
Accessing the Internet by Bridge Mode
1.Login the WebGUI and set the
Operation Mode
as
Bridge Mode
.
2.Connect the device with internet by
WAN/LAN
.
Accessing the Internet by Cable Broadband
1.Login the WebGUI and set the
Operation Mode
as
Cable Broadband.
Page 14 / 39
10
2.Connect the device with internet by
WAN
.
3.Set
WAN Connection
in WebGUI.
Accessing the Internet by 3G Gateway
Note: Please make sure that you have install (U)SIM card before you switch on the device.
1.Login the WebGUI and set the
Operation Mode
as
3G Gateway
.
2. Set
WAN Connection
in WebGUI.
Accessing the WebGUI Configuration Page
1. Make sure the connection between your device and the client is correct.
2. Launch the internet browser and enter
in the address bar.
Notes:
It is recommended that you use IE (6.0 or later), Firefox (2.0 or later), Opera (10.0 or later), Safari
(4.0 or later) or Chrome (5.0 or later).
3.
The login page appears as follows.
Page 15 / 39
11
Login
In the WebGUI Configuration page, select the desired language and input the password (the default
Password
is
admin
).
Click
Login
to log in the device.
Notes:
If you check
Save
after type in password, the device will save it. Next time when you want to login the
device with the same password, what you need to do is click
Login
.
When you login, the following interface appears.
19216811.live