Zoom 5363 Router Manual PDF (Setup & Configuration Guide)

Page 26 / 142 Scroll up to view Page 21 - 25

folders or devices such as printers. Most users should select

Yes

. If you know you

don’t want to share files or devices, select

No

.

Repeat steps 1-5 above for each Windows computer you want to connect to the Cable

Modem/Router. If you want to connect a non Windows computer or another device such

as a tablet, follow the instructions below.

26

Page 27 / 142

If you are using a non Windows computer or other device that supports

WPS

Please refer to the instructions for your device for more information on using WPS.

The

directions below should work for most users.

1

Press the

WPS

LED pushbutton on the front panel of the router for at least 3

seconds. The WPS LED should blink orange.

2

Within 2 minutes (before the WPS LED orange light turns off), press the WPS button

on the device that you’re linking wirelessly to the modem/router. The button may be a

physical pushbutton on the device or a button on a page of the device’s wireless

network configuration menus.

3

Congratulations! You should now have a secure connection between your Cable

Modem/Router and a device. Now is a good time to check that your device’s Internet

connection is working. Open your browser and go to a familiar Web site. If you are

able to connect, continue with the next step below.

If you are not able to connect to the Internet, please see

Appendix A:

Troubleshooting Tips

.

4

If you have other devices whose WPS security you need to set, repeat steps 1

through 3 for each device. When they are finished, the basic setup for these local

wireless devices should be complete

.

27

Page 28 / 142

Connecting Additional Computers and/or Other Devices to the

Cable Modem/Router’s Ethernet/LAN ports

You can plug up to four computers, game consoles, or other Ethernet-capable devices into the

Cable Modem/Router’s LAN ports. For information about your specific device, please refer

to the documentation that came with that device. Follow the instructions below for each

computer or other device.

1

If you connected the Cable Modem/Router to a computer using a wired connection

when setting up the Cable Modem/Router, unplug the computer now if you don’t

want that computer to stay connected to the Cable Modem/Router.

2

To connect a computer or other Ethernet-capable device, plug one end of an

Ethernet cable into an available Ethernet (LAN 1, 2, 3, or 4) port on the Cable

Modem/Router and plug the other end of the Ethernet cable into the Ethernet port of

the additional device you want to connect to the Cable Modem/Router. (If you are

connecting a hub or a switch, this is typically called an Uplink or Expansion port.)

If

you are connecting a computer or game station, go to step 5 of this section.

3

If you are connecting a network device such as a switching hub, use the instructions

that came with that device. Then reboot any computer that is part of your network.

For example, if you connected a switching hub, reboot any computer that will be

connected to that switching hub.

4

If you are connecting a HomePlug adapter pair with one adapter plugged into the

Cable Modem/Router and an AC outlet, and the other adapter plugged into a

computer, game station, or other device and an AC outlet, make those connections

and then go to step 5.

5

Verify that your Internet connection is working. Open a Web browser on each

computer that’s using your network and try to connect to a familiar Web address.

Congratulations! You have connected an additional device to the Internet. You can

connect up to 4 Ethernet-capable devices to the Cable Modem/Router, following the

instructions above for each device by starting at step 2 of this section.

28

Page 29 / 142

4

Changing the Default Wireless Settings

Your Cable Modem/Router comes from the factory with a default SSID (Wireless

Network Name),

WPA-PSK/WPA2-PSK

wireless security and a random Wireless

Security Key (Wireless Password). These default settings for your router are listed on the

bottom label of your unit. Most users can go ahead and use the default settings.

You may want to change your wireless settings if the wireless devices on your network

are already configured to use an existing wireless network name and password. Instead

of having to reconfigure all the devices on your network, you can change the Cable

Modem/Router to match the existing settings used by your devices. Read this chapter if

you want to use another wireless security mode, or if you want to change either the SSID

or Wireless Security Key. If you want to use the default wireless settings, you can skip

this chapter.

About Wireless Security

There are two basic wireless security modes, WPA and WEP. There are two versions of

WPA: WPA and WPA2. When configured as part of a typical home or small office

network, WPA and WPA2 require a Pre-Shared Key, or PSK. These modes are typically

called WPA-PSK and WPA2-PSK, respectively, though sometimes they’re just called

WPA and WPA2. You can enable either WPA-PSK or WPA2-PSK alone, or you can

enable both WPA-PSK and WPA2-PSK together. By default, your Cable Modem/Router

has both WPA-PSK and WPA2-PSK enabled. You will only need to change the security

mode if you know that you have a device you are connecting to your wireless network

that only supports WEP go to

Setting up Security using WEP

.

In the unlikely event that

you want an unsecured network, this is discussed late in this chapter in

Disabling

Security

.

Note:

If you have a Radius Server (very unlikely for a home network), select the

WPA/WPA2 options without PSK. All instances of WPA and/or WPA2 that follow refer to

WPA-PSK and/or WPA2-PSK unless noted otherwise.

29

Page 30 / 142

You can check to see if all other clients that you plan to put on the network support WPA

or WPA2. You can do this by checking the manual that came with each device or by

checking the configuration software for the installed device. Look under

Security

or

Encryption

or

Setup

or

Advanced Features

. Most devices will support one of these

modes.

•

To change the Wireless Network Name (SSID) or Wireless Security Key

(Pre-Shared key) used by your Cable Modem/Router go to

Changing your

Wireless Network Name(SSID) and Pre-Shared Key

.

•

If any of the devices you want to connect to your wireless network do not support

WPA or WPA2, go to

Setting Up Security Using WEP

.

•

If you need to set up an unsecured network, see

Disabling Security

.

Changing your Wireless Network Name (SSID) and Pre-Shared

Key

Most likely your previous wireless network used 802.11n. If you want to change your

Cable Modem/Router settings to match your existing network settings follow the steps

below.

If you have newer devices that support 802.11ac then you should connect to

the Cable Modem/Router’s 5G network. For instructions on connecting to the 5G

network refer to

Chapter 3, Connecting other Devices to the Cable Modem/Router

.

To check if your device supports 801.11ac, you can scan for available wireless networks

on your device.

If you see a wireless network named

Zoomxxxx_5G

than your devices

supports 802.11ac and you should follow the instructions for connecting that device to

the Cable Modem/Router found in Chapter 3. If you only see

Zoomxxxx

then your

device does not support 802.11ac. In both cases, xxxx are the last 4 characters of the

cable modem CM MAC address. You can find

Zoomxxxx

printed on the bottom label of

your Cable Modem/Router.

1

Open the Zoom Configuration Manager by typing the following in your Web browser's

address bar:

http://192.168.0.1

2

In the

Login

dialog box, type the following User Name and Password in lower case,

then click

Login

.

User Name:

admin

Password:

admin

30

Rate

Popular Zoom Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share