In this case the same ports are used for both incoming and outgoing traffic, so we would

use the same ports as both the triggering port and the target port as shown below.

To setup

port triggering

for World of Warcraft:

1

Launch a Web browser.

2

In the browser address bar, type

and press the

Enter

key.

3

In the Login screen, enter:

default username:

admin

default password:

admin

Both the username and password are case sensitive. The default username and

password are printed on the label of your unit. When the cable modem is standing

vertically this label is located on the side of your modem.

4

Click the Login button to access the Cable Modem/Router. The

Status

page

appears.

5

Click

Advanced

in the menu bar.

6

Then click the

Port Triggers

submenu. The

Port Triggers

page appears. Click

Create button to create rules.

7

We will need to setup 5 triggers for World of Warcraft.

The first rule would cover

ports 1119-1120. Enter 1119 in the

Trigger Start Port

field and 1120 in the

Trigger

36

End Port

field. Since these ports are used to send data both directions enter 1119 in

the

Target Start Port

and 1120 in the

Target End Port

.

8

Select

TCP

in the

Protocol

drop down menu since these ports use TCP.

9

Enter a name for this rule, for example WOW1. Click

Enable

then click

Apply

. Your

new rule will appear in the table.

10

Repeat steps 7-9 for the next rule.

In this case only one port is used, 3724.

Enter

3724 in the

Trigger Start/End Port

and

Target Start/End Port

fields.

11

Repeat steps 7-9 for the remaining ports that need to be opened.

When you are

complete the table should look like this:

If your online game does not work and you are sure that you entered the correct ports

on the port triggering page, check to see if you have a firewall running on your

computer that is preventing you from playing your online game. This firewall may be

either the built-in Windows firewall or may be part of a third party security package

you are using on your computer. You will need to allow access through these

firewalls to be able to play your online game.

37

6

Advanced Settings

Advanced Setup is primarily for technically advanced users. For most people, the

options that are set by default when the Cable Modem/Router is installed are sufficient.

However, those who want or need to change the default settings can do so using the

advanced setup pages in the

Zoom Configuration Manager

.

This chapter includes:

•

Suggestions for settings that you might want to change

•

Instructions for launching the Zoom Configuration Manager

program

•

An overview of the available configuration menus and settings and a guide on

what chapter to go to for more information on each settings.

Changing Default Settings

Here are some reasons why you might want to use the Configuration program to change

the router's default settings.

•

•

•

•

•

•

Your Cable provider instructs you to enable, disable, or change the default settings

for your router

You want to change your router’s password to help prevent hacker attacks.

You want to set up a wireless guest network to give users access to the internet but

not your internal network.

You want to change the default firewall settings to block particular IP addresses and

intrusive hosts.

You want to access your corporate network and need to use the built-in VPN

function.

You wish to control the hours that a user on your network can access the Internet.

38

Accessing the Zoom Configuration Manager

From your Web browser, you will log in to the interface to define system parameters,

change password settings, view status windows to monitor network conditions, and

control the Cable Modem/Router and its ports.

To access the Zoom Configuration Manager, use the following procedure:

1

Launch a Web browser.

Note:

Your computer does not have to be online to configure your Cable

Modem/Router.

2

In the browser address bar, type

and press the

Enter

key.

For example:

The Login screen appears (see Figure 1)

Figure 1. Login Screen

3

In the Login screen, enter:

default username:

admin

default password:

admin

4

Click the Login button to access the Cable Modem/Router. The

Status

page

39

appears, showing connection status information about your Cable Modem/Router

After you log in to the Zoom Configuration Manager interface, we strongly recommend

that you change the default password as follows:

1

On the left hand menu click on

Security

.

2

Enter

admin

in the User Name dialog box. The default user name can not be

changed

3

Enter the default password,

admin

in the

Current Password

dialog box.

4

Enter your new password in the

New Password

box. Your new password can be

from 1 to 8 characters long and can contain either letters or numbers.

The

password and username are case sensitive, so notice which letters are capitalilzed.

5

In the

Re-Enter New Password

box enter your new password again and click

Apply

. Your new password is now active. We recommend you write you new

password down on a label and attach it to your Cable Modem/Router. If you forget

your new password in the future, you can reset the Cable Modem/Router to its

default settings by pressing the Reset button for 8 seconds. This will change the login

back to the default User Name

admin

and the default password

admin

.

6

If you only wanted to change your password, you’re done. If you want to do

something else with the Configuration Manager, continue below to

Understanding

the Configuration Manager Interface Screens

.

Understanding the Configuration Manager Interface Screens

The top of the management interface contains a menu bar you use to select menus for

configuring the Cable Modem/Router. When you click a menu item, information and any

configuration settings associated with the menu appear in the main area of the interface

(see Figure 2). If the displayed information exceeds what can be shown in the main area,

scroll bars appear to the right of the main area so you can scroll up and down through the

information.

40