Page 36 / 123 Scroll up to view Page 31 - 35
Operation and Status
33
Data - Status Screen
Connection Method
This indicates the current connection method, as set in the Setup
Wizard.
Broadband Modem
This shows the connection status of the modem.
Internet Connection
Current connection status:
Active
Idle
Unknown
Failed
If there is an error, you can click the "Connection Details" button
to find out more information.
Internet IP Address
This IP Address is allocated by the ISP (Internet Service Pro-
vider).
"Connection Details"
Button
Click this button to open a sub-window and view a detailed
description of the current connection. Depending on the type of
connection, a "log" may also be available.
IP Address
The IP Address of the TW100-BRV204.
Network Mask
The Network Mask (Subnet Mask) for the IP Address above.
DHCP Server
This shows the status of the DHCP Server function - either
"Enabled" or "Disabled".
For additional information about the PCs on your LAN, and the
IP addresses allocated to them, use the
PC Database
option on
the
Advanced
menu.
Device Name
This displays the current name of the TW100-BRV204.
Firmware Version
The current version of the firmware installed in the TW100-
BRV204.
"System Data"
Button
Clicking this button will open a Window which lists all system
details and settings.
Connection Details
View the details of the current Internet connection. The sub-
screen displayed will depend on the connection method used. See
the following sections for details of each sub-screen.
System Data
Display all system information in a sub-window.
Restart Router
Restart (reboot) the Router. You will have to wait for the restart
to be completed before continuing.
Refresh Screen
Update the data displayed on screen.
Page 37 / 123
TW100-BRV204 User Guide
34
Connection Status - PPPoE
If using PPPoE (PPP over Ethernet), a screen like the following example will be displayed
when the "Connection Details" button is clicked.
Figure 22: PPPoE Status Screen
Data - PPPoE Screen
Physical Address
The hardware address of this device, as seen by remote devices
on the Internet. (This is different to the hardware address seen by
devices on the local LAN.)
IP Address
The IP Address of this device, as seen by Internet users. This
address is allocated by your ISP (Internet Service Provider).
Network Mask
The Network Mask associated with the IP Address above.
PPPoE Link Status
This indicates whether or not the connection is currently estab-
lished.
If the connection does not exist, the "Connect" button can be
used to establish a connection.
If the connection currently exists, the "Disconnect" button
can be used to break the connection.
Connection Log
The Connection Log shows status messages relating to the
existing connection.
The most common messages are listed in the table below.
The "Clear Log" button will restart the Log, while the Re-
fresh button will update the messages shown on screen.
Page 38 / 123
Operation and Status
35
Connect
If not connected, establish a connection to your ISP.
Disconnect
If connected to your ISP, hang up the connection.
Clear Log
Delete all data currently in the Log. This will make it easier to
read new messages.
Refresh
Update the data on screen.
Connection Log Messages
Connect on Demand
Connection attempt has been triggered by the "Connect
automatically, as required" setting.
Manual connection
Connection attempt started by the "Connect" button.
Reset physical connection
Preparing line for connection attempt.
Connecting to remote
server
Attempting to connect to the ISP's server.
Remote Server located
ISP's Server has responded to connection attempt.
Start PPP
Attempting to login to ISP's Server and establish a PPP
connection.
PPP up successfully
Able to login to ISP's Server and establish a PPP connection.
Idle time-out reached
The connection has been idle for the time period specified in
the "Idle Time-out" field. The connection will now be termi-
nated.
Disconnecting
The current connection is being terminated, due to either the
"Idle Time-out" above, or "Disconnect" button being clicked.
Error: Remote Server not
found
ISP's Server did not respond. This could be a Server problem,
or a problem with the link to the Server.
Error: PPP Connection
failed
Unable to establish a PPP connection with the ISP's Server.
This could be a login problem (name or password) or a Server
problem.
Error: Connection to
Server lost
The existing connection has been lost. This could be caused
by a power failure, a link failure, or Server failure.
Error: Invalid or unknown
packet type
The data received from the ISP's Server could not be proc-
essed. This could be caused by data corruption (from a bad
link), or the Server using a protocol which is not supported by
this device.
Page 39 / 123
TW100-BRV204 User Guide
36
Connection Status - PPTP
If using PPTP (Peer-to-Peer Tunneling Protocol), a screen like the following example will be
displayed when the "Connection Details" button is clicked.
Figure 23: PPTP Status Screen
Data - PPTP Screen
Physical Address
The hardware address of this device, as seen by remote devices on
the Internet. (This is different to the hardware address seen by
devices on the local LAN.)
IP Address
The IP Address of this device, as seen by Internet users. This address
is allocated by your ISP (Internet Service Provider).
PPTP Status
This indicates whether or not the connection is currently established.
If the connection does not exist, the "Connect" button can be
used to establish a connection.
If the connection currently exists, the "Disconnect" button can be
used to break the connection.
Connection Log
The Connection Log shows status messages relating to the
existing connection.
The "Clear Log" button will restart the Log, while the Refresh
button will update the messages shown on screen.
Connect
If not connected, establish a connection to your ISP.
Page 40 / 123
Operation and Status
37
Disconnect
If connected to your ISP, hang up the connection.
Clear Log
Delete all data currently in the Log. This will make it easier to read
new messages.
Refresh
Update the data on screen.
Connection Status - Telstra Big Pond
An example screen is shown below.
Figure 24: Telstra Big Pond Status Screen
Data - Telstra Big Pond Screen
Physical Address
The hardware address of this device, as seen by remote devices.
(This is different to the hardware address seen by devices on the
local LAN.)
IP Address
The IP Address of this device, as seen by Internet users. This
address is allocated by your ISP (Internet Service Provider).
Connection Status
This indicates whether or not the connection is currently estab-
lished.
If the connection does not exist, the "Connect" button can be
used to establish a connection.
If the connection currently exists, the "Disconnect" button can
be used to break the connection.
Normally, it is not necessary to use the Connect and Discon-
nect buttons unless the setting "Connect automatically, as
required" is disabled.

Rate

4.5 / 5 based on 2 votes.

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top