Page 11 / 13 Scroll up to view Page 6 - 10
Q1:
A1:
Q2:
A2:
Q3:
A3:
Q4:
A4:
Q5:
A5:
Q6:
A6:
Q7:
A7:
The Image is blurry.
How can I adjust the focus on the Internet camera?
You can adjust the Internet Camera’s focus by rotating the lens.
IP Setup is unable to detect my camera.
What should I do?
First, verify that you have followed all the steps in the Section 2: Hardware Installation.
Second, disable any software firewall programs such as ZoneAlarm or Norton Internet
Security.
If you are using Windows XP or Windows Vista, disable the built in firewall.
Third,
click on Search in the IPSetup setup wizard.
I do not have a DHCP server or DHCP is disabled on my network and I am unable to
configure the TV-IP110/TV-IP110W.
What should I do?
First, go to the TCP/IP settings on your computer and assign a static IP address on your
computer's network adapter in the subnet of 192.168.10.x.
Since default IP address of the
TV-IP110/W is 192.168.10.30, do not assign a static IP address of 192.168.10.30 on your
computer's network adapter.
Second, run the IPSetup wizard and double click on the
TV-IP110/TV-IP110W to access the browser configuration.
When I click on Live View the image does not load?
First, make sure that you are using a browser that supports ActiveX.
Second, make
sure that you added ActiveX.
See step 10 and 11 in Section 2:
Configure the Internet
Camera
.
How do I connect the TV-IP110W to my wireless router or access point?
Make sure that you configure the camera to have the same SSID, encryption mode and
key (if enabled).
Follow the instructions in section 2 to configure the camera with the SSID
and encryption key.
After I successfully configured the TV-IP110W to match my wireless network settings, I
can not connect to the camera.
First, verify that the wireless settings match your wireless network settings.
Second,
verify in the wireless section of the browser configuration that the
Enable
option is checked.
Third, make sure to disconnect the Ethernet cable from the camera and verify that the
LINK
LED is blinking green.
I forgot my password.
What should I do?
Take a pin or paperclip and press the reset button on the back of the unit for 15 seconds.
This will return settings back to factory defaults.
The default IP address is 192.168.10.30.
The default administrator ID and password is admin.
If you still encounter problems or have any questions regarding the
TV-IP110/TV-IP110W
, please
contact TRENDnet’s Technical Support Department.
9
Troubleshooting
Page 12 / 13
Certifications
This equipment has been tested and found to comply with FCC and CE Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received. Including interference that may
cause undesired operation.
NOTE:
THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV
INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS
EQUIPMENT.
SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO
OPERATE THE EQUIPMENT.
Waste electrical and electronic products must not
be disposed of with household waste. Please
recycle where facilities exist. Check with you Local
Authority or Retailer for recycling advice.
ADVERTENCIA
En todos nuestros equipos se mencionan claramente las caracteristicas del adaptador de
alimentacón necesario para su funcionamiento.
El uso de un adaptador distinto al
mencionado puede producir daños fisicos y/o daños al equipo conectado.
El adaptador
de alimentación debe operar con voltaje y frecuencia de la energia electrica domiciliaria
existente en el pais o zona de instalación.
Page 13 / 13
Copyright ©2008. All Rights Reserved. TRENDnet.
Product Warranty Registration
Please take a moment to register your product online.
Go to TRENDnet’s website at http://www.trendnet.com/register
20675 Manhattan Place
Torrance, CA 90501
USA

Rate

4.5 / 5 based on 2 votes.

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top