Page 6 / 12 Scroll up to view Page 1 - 5
English
4
2.
Click on
Search device
, and then
select the Storage Server.
3.
Configure the
IP (IP address)
,
Network
(
Subnet mask)
,
Gateway
and then click
Modify
.
Note: The IP Address must match
the network segment of your
network.
3. Configure the Storage Server
Note: Install and use the Easy Search Utility to discover all the TS-I300/TS-
I300W on the network, assign IP Address, change the host name and
workgroup, and mount or unmount the hard drive.
For Windows Users
1.
Insert the
Utility CD-ROM
into
your computer's CD-ROM Drive
and then click
Easy Search Utility
.
4.
Click
Connect to webpage
.
Page 7 / 12
English
5
5.
Click
Format Hard Drive
.
6.
Click
OK
.
7.
Click
Restart.
8.
Click
OK.
Note: If your hard drive has already been formatted, please skip to step 9.
If
you are attaching a brand new hard drive, please continue on to step 5.
Page 8 / 12
English
6
9.
Enter the User name and
Password, and then click
Config
.
User Name:
admin
Password:
admin
10.
Click
Advanced
and then
Wireless.
Note: For the TS-I300 skip to section 4.
For the TS-I300W continue on to step
10.
11.
Click
Access Point
, and then
click
Enable.
Enter an SSID and
then click
Apply
.
Your configuration is now complete.
For detailed information regarding the
TS-I300/TS-I300W's
configuration and
advanced settings, please refer to the Troubleshooting section, User's Guide
CD-ROM, or TRENDnet's website at http://www.trendnet.com.
Page 9 / 12
English
7
1.
Select the hard drive, and then
click
Mount
.
2.
Click
OK
.
3.
Double-click on
My Computer
.
Then double-click on any mounted
hard drive under
Network Drives
.
4. Accessing Storage Devices on TS-I300/TS-I300W
Your storage device is ready for access
Page 10 / 12
8
Q1:
A1:
Q2:
A2:
Can I connect or disconnect the USB storage device while the TS-I300/TS-I300W is on?
Yes, you can connect or disconnect any external USB device while the computer is on,
I specified the IP address http://192.168.1.2 in my Internet Browser's Address Bar, but
an error message says “The page cannot be displayed.” How can I get into the TS-I300/TS-
I300W's web configuration page?
First, check your hardware settings again by following the instructions in section 2.
Second, make sure the LAN and WLAN (TS-I300W) lights are lit.
Third, make sure the
because the USB interfaces are Plug-and-Play and hot-pluggable.
Just press on the
Unmount button on the unit or open the utility program and press unmount for the USB
device.
TS-I300/TS-I300W is assigned an IP Address in the same subnet as your network.
You may
need to adjust the TCP/IP settings on your computer to match the storage server.
Please
see the steps below:
Troubleshooting
1.
Go into the
Control Panel
and double-click
the
Network Connections
icon, right-click
the
Local Area Connection
icon and then
click
Properties
.
2.
Click
Internet Protocol (TCP/IP)
and then
click
Properties
.
Then click on
Use the
following IP address
, and make sure you
assign your network adapter an IP address
in the subnet of 192.168.1.x.
Q3:
A3:
I am unable to mount or access the IDE hard drive.
What should I do?
First, verify that the IDE hard drive has been properly installed (see section 2).
Second,
disable any software firewall programs (e.g. Norton Internet Security, McAfee).
If you are
running Windows XP, disable the built-in XP firewall.
Third, make sure the
TS-I300/TS-I300W is assigned an IP Address in the same subnet as your network.

Rate

4.5 / 5 based on 2 votes.

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top