Page 6 / 9
Scroll up to view Page 1 - 5
4
Troubleshooting
Q1:
How do I configure TCP/IP settings on my computer?
1.
Go into the
Control Panel
and double-
click the
Network Connections
icon,
right-click the
Local Area Connection
icon and then click
Properties
.
2.
Click
Internet Protocol (TCP/IP)
and
then click
Properties
.
Then click on
Use the following IP address
, and
make sure you assign your network
adapter an IP address in the subnet of
192.168.223.x.
Q2:
A2:
Q3:
A3:
If my network's IP is different than the PoE Switch's range, what should I do?
You should still configure the PoE Switch first. After all the settings are
applied, go to the PoE Switch's configuration page, click on IP settings and change
the IP address of the PoE Switch to match your network's IP.
error message says “The page cannot be displayed.” How can I get into the TPE-
80WS's web configuration page?
First, check your hardware settings again by following the instructions in
section 2.
Second, make sure the POWER and LINK/ACT lights are lit.
Third,
make sure the TCP/IP settings are configured properly (see Q1).
Fourth, since
the PoE Switch’s default IP address is
192.168.223.100, make sure that no other
Page 7 / 9
Q4:
A4:
Q5:
A5:
Q6:
A6:
I forgot the administration password.
How do I reset my TPE-80WS?
Press on the default button using a pen or paperclip for 10 seconds.
The
default password is admin.
What are the default port settings for configuring the Switch through the
console port using HyperTerminal?
Bits per Second: 115200; Data bits: 8; Parity: None; Stop bits: 1; Flow control:
None; Emulation: VT100.
If you still encounter problems or have any questions regarding the TPE-80WS, please
contact TRENDnet’s Technical Support Department.
My 802.3af Powered device does not power on when I plug the device into
the Switch.
What should I do?
First, verify that your PoE device supports IEEE 802.3af protocol.
Second,
verify that your PoE device powers up using its power adapter.
Third, power cycle
the PoE switch.
Unplug power to the switch, wait 15 seconds, then plug the
power back in.
Fourth, plug the device into a different port on the PoE switch.
Fifth, try using another Cat-5e cable.
5
Page 8 / 9
Certifications
This equipment has been tested and found to comply with FCC and CE Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received. Including interference that may
cause undesired operation.
NOTE:
THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV
INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS
EQUIPMENT.
SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO
OPERATE THE EQUIPMENT.
Waste electrical and electronic products must not
be disposed of with household waste. Please
recycle where facilities exist. Check with you Local
Authority or Retailer for recycling advice.
ADVERTENCIA
En todos nuestros equipos se mencionan claramente las caracteristicas del adaptador de
alimentacón necesario para su funcionamiento.
El uso de un adaptador distinto al
mencionado puede producir daños fisicos y/o daños al equipo conectado.
El adaptador
de alimentación debe operar con voltaje y frecuencia de la energia electrica domiciliaria
existente en el pais o zona de instalación.
Page 9 / 9
Product Warranty Registration
TRENDnet Technical Support
US
Canada
24/7 Tech Support
Toll Free Telephone:
1(866) 845-3673
Europe
(Germany
France
Italy
Spain
Switzerland
UK)
English/Espanol - 24/7
Francais/Deutsch - 11am-8pm, Monday - Friday MET
English/Espanol - 24/7
Francais/Deutsch - 11am-8pm, Monday - Friday MET
Worldwide
Telephone:
+(31) (0) 20 504 05 35
Toll Free Telephone:
+00800 60 76 76 67
.
.
.
.
.
.
Copyright ©2007. All Rights Reserved. TRENDnet.
Please take a moment to register your product online.
20675 Manhattan Place
Torrance, CA 90501
USA
19216811.live