1. Home
    2. /
  2. Manuals
    3. /
  3. TRENDnet
    4. /
  4. TEW-811DRU
    5. /
  5. 9
Page 41 / 68 Scroll up to view Page 36 - 40
© Copyright 2013 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
TEW-811DRU
41
•
Match Protocol:
Select the protocol to be forwarded to the device.
TCP
or
UDP.
•
Match Port:
Enter the ports or port range to be forwarded to the device. (e.g.
2000-2038 ,2200-2210).
•
Trigger Protocol:
Select the protocol requested by the device.
TCP
or
UDP.
•
Trigger Port:
Enter the ports or port range requested by the device. (e.g.
554-554
or 6112-6112).
Note:
Please refer to the device documentation to determine which ports and
protocols are required.
•
Schedule:
Select the defined schedule you would like to have the rule to be
applied (see “
Create Schedule
” section on page 38).
•
Enabled:
Selecting
Enabled
turns on the virtual server and selecting unchecking
disables the rule.
Gaming
Advanced > Gaming
Gaming allows you to define multiple ports (used or required by a specific application or
game) and forward them to a single IP address (a computer or device) on your network.
Using this feature is more secure compared to using DMZ (see “
DMZ
” on page 39) in
which DMZ forwards all ports instead of only specific ports used by an application. Since
most ISPs constantly change your home IP address, to be able to access the Virtual
Server port(s) from the Internet it is recommended to setup Dynamic DNS service (see
“
Identify your network over the Internet
” section on page 37).
1. Log into your router management page (see “
Access your router management page
”
on page 31).
2. Click on
Advanced
, and click on
Gaming
.
3. Click on
Enabled
under
Gaming Function
section.
3. Review the virtual server settings. Click
Apply
to save settings.
•
LAN IP Address:
Enter the IP address of the device to forward the port (e.g.
192.168.10.101)
.
•
TCP Ports to Open
: Enter the TCP port you would like to set.
•
UDP Ports to Open
: Enter the UDP port you would like to set.
Note:
Please refer to the device documentation to determine which ports and
protocols are required.
You should assign a static IP address to the device or
use DHCP reservation to ensure the IP address of the device does not change.
•
Schedule:
Select the defined schedule you would like to have the rule to be
applied (see “
Create Schedule
” section on page 38).
•
Enabled:
Selecting
Enabled
turns on the virtual server and selecting unchecking
disables the rule.
Allow remote access to your router management page
Advanced > Advanced Network
You may want to make changes to your router from a remote location such at your
office or another location while away from your home.
1. Log into your router management page (see “
Access your router management page
”
on page 31).
2. Click on
Administrator
, and click on
Management
.
3. Review the setting on
the Remote Management
section. Click
Apply
to save settings
Page 42 / 68
© Copyright 2013 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
TEW-811DRU
42
•
Remote Control:
Select enable or disable for the feature.
•
Port:
Enter the port to assign remote access to the router. It is recommended to
leave this setting as 8080.
Note:
If you have configured port 8080 for another configuration section such
as virtual server or special application, please change the port to use.
(Recommended port range 1024-65534)
Prioritize traffic using QoS (Quality of Service)
Network > QoS
You may want to prioritize traffic for specific computers or devices on your network to
have higher priority. QoS involves prioritization of network traffic. QoS can be targeted
at a network interface, toward a given server or router's performance, or in terms of
specific applications.
1. Log into your router management page (see “
Access your router management page
”
on page 31).
2. Click on
Network
, and click on
QoS
.
3. Review the QoS settings.
•
Enable QoS:
Enable or Disable the Quality of service through the router.
•
Prioritize ACK:
Enable or disable ACK prioritization.
•
Prioritize ICMP:
Enable or disable ICMP prioritization.
3. Select the traffic class you would like to configure for your QoS rule.
4. Review the
Inbound/Outbound Class Setting
section.
•
BW Max Inbound:
Enter the maximum download speed of your ISP (Internet
Service Provider).
•
Highest/High/Medium/Low/Lowest:
Enter the download speeds you would like
to apply on each state of download speeds. This setting is similar to setting the
priority speeds of each class
Page 43 / 68
© Copyright 2013 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
TEW-811DRU
43
6. Review the
QoS Rule
settings.
•
IP/MAC Address Filter:
Select from the pull down menu the IP address or MAC
you would like to apply and enter the IP address of MAC address.
•
Protocol Filter:
Select the protocol you would like to apply on the QoS Rule.
•
Port Filter:
Select the port from the pull down menu you would like to assign on
the QoS rule and enter the port.
•
Class Assigned:
Select from the pull down menu the class you applied on the
previous section you would like to assign the QoS rule.
•
Description: Enter the QoS description that best describes the rule.
7. Click
Add Rule
to add and save the rule to the QoS Rule List
.
Add static routes to your router
Advanced > Routing
You may want set up your router to route computers or devices on your network to
other local networks through other routers. Generally, different networks can be
determined by the IP addressing assigned to those networks. Generally speaking and for
the case of an example, your network may have 192.168.10.x IP addressing and another
network may have 192.168.20.x IP addressing and because the IP addressing of these
two networks are different, they are separate networks. In order to communicate
between the two separate networks, static routing needs to be configured. Below is an
example diagram where routing is needed for devices and computers on your network
to access the other network.
Note:
Configuring this feature assumes that you have some general networking
knowledge.
1. Log into your router management page (see “
Access your router management page
”
on page 31).
2. Click on
Advanced
, and click on
Routing
.
3. Review the
LAN/WAN Static Routes
section. Click
Apply
to save settings.
•
IP Address:
Enter the IP network address of the destination network for the
route. (e.g.
192.168.20.0
)
•
Subnet Mask:
Enter the subnet mask of the destination network for the
route.(e.g.
255.255.255.0
)
•
Gateway:
Enter the gateway to the destination network for the route.
(e.g.
192.168.10.2
)
•
Metric:
Enter the metric or priority of the route. The metric range is
1-15
, the
lowest number
1
being the highest priority. (e.g.
1
)
Page 44 / 68
© Copyright 2013 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
TEW-811DRU
44
Using External USB Storage
Your router’s USB port can be used to share files through the network when a USB
storage device is connected on the back USB port. The router supports both FTP and
SAMBA (SMB) filing sharing protocols.
Samba Network File Server
Administrator > File Sharing
Samba is a network protocol that allows you to access shared files through your
network. In order to share files, you will need to plug in a USB storage device on the USB
port on the back of the router. You can access these files under your network map or by
typing
\\routerIPaddress
on your browser’s address bar. Please follow the below steps
to configure the router’s Samba settings
1. Log into your router management page (see “
Access your router management page
”
on page 31).
2. Click on
Administrator
, and click on
File Sharing
.
3. Review the setting on
Samba Server Information
section. Click
Apply
to save settings
•
Server Status:
Select enable or disable for the feature.
•
Server Name:
Enter the name of your server.
•
Workgroup:
Enter the work group of your server.
•
Description:
Enter a description of the server.
4. Review the administrator settings required for your
Samba server
. Click
Apply
to save
settings. Administrator will have read and write access to files. To define user
accounts continue to the next step.
•
User Name:
Enter the user name to be used to access your files.
•
Password:
Enter the password for the user name.
5. Review the
User Account List
section. Click
Apply
to save settings
•
User Name:
Enter the user name to be used to access your files.
•
Password:
Enter the password for the user name.
•
Permission:
Select the permission you will grant to the user
•
Enabled:
Click to activate user account.
Page 45 / 68
© Copyright 2013 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
TEW-811DRU
45
FTP (File Transfer Protocol) Server
Administrator > File Sharing
FTP (File Transfer Protocol) is used to access shared files through the Internet. In order
to share files, you will need to plug in a USB storage device on the USB port on the back
of the router. Signing up for a Dynamic DNS service (outlined in
Identify Your Network
section pg.39) will provide identification of the router’s network from the Internet. You
can access your shared files by typing ex.
ftp://router’sWANIPaddress
or
ftp://myDDNSservice
. Please follow the steps below to configure the router’s FTP
settings
1. Log into your router management page (see “
Access your router management page
”
on page 31).
2. Click on
Administrator
, and click on
File Sharing
.
3. Review the setting on
Samba Server Information
section. Click
Apply
to save settings
•
Server Status:
Select enable or disable for the feature.
•
Language:
Select your language.
4. Review the administrator settings required for your
FTP server
. Click
Apply
to save
settings
•
User Name:
Enter the user name to be used to access your files.
•
Password:
Enter the password for the user name.
5. Review the
User Account List
section. Click
Apply
to save settings
•
User Name:
Enter the user name to be used to access your files.
•
Password:
Enter the password for the user name.
•
Permission:
Select the permission you will grant to the user
•
Enabled:
Click to activate user account.

Rate

124.8 / 5 based on 304 votes.

Popular TRENDnet Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top