TRENDnet TEW-639GR Router Manual PDF (Setup & Configuration Guide)

Page 6 / 13 Scroll up to view Page 1 - 5

4

Note:

The example below is for WPA2-PSK security.

If you select WPA-PSK or

WPA2-PSK, make sure your wireless adapters support WPA2 or WPA.

If your wireless

adapters do not support WPA or WPA2, then select WEP.

Your Installation is complete

Register Your Product

To ensure the highest level of customer service and support, please take a moment to

register your product Online at:

www.trendnet.com/registe

r

Thank you for choosing TRENDnet

For detailed information regarding the

TEW-639GR

’s

configuration and advanced settings,

please refer to the Troubleshooting section, User's Guide on the Utility CD-ROM, or

TRENDnet's website at http://www.trendnet.com.

6.

Select the desired

WPA

mode, enter characters

for your Pre-Shared key and then click

Apply

.

For WPA-PSK or WPA2-PSK, the Pre-Shared

Key must be between 8 and 63 ASCII or 64

HEX characters.

Make sure to copy down the

Pre-Shared Key.

7.

Open up your browser and enter in a URL (e.g.

www.trendnet.com) to verify that you have

Internet connection.

Page 7 / 13

1. I typed http://192.168.10.1 in my Internet Browser's Address Bar, but an error message

says “The page cannot be displayed.” How can I get into the TEW-639GR's web

configuration page?

Check your hardware settings again by following the instructions in Section 2.

2. Make sure the LAN and WLAN lights are lit.

3. Make sure your TCP/IP settings are set to

Obtain an IP address automatically

(see the

steps below).

1.

4. Press on the factory reset button for 15 seconds.

Troubleshooting

5

Windows 7

1.

Go into the

Control Panel

, click

Network and

Internet

, click

Network and Sharing Center

, click

Manage Network Connections

and then right-click

the

Local Area Connection

icon and then click

Properties

.

Windows Vista

1.

Go into the

Control Panel

, click

Network and

Sharing Center

, click

Change Adapter Settings

and then right-click the

Local Area Connection

icon and then click

Properties

.

2.

Click

Internet Protocol Version 4(TCP/IPv4)

and then click

Properties.

Then

click on

Obtain an IP address automatically.

2.

Click

Internet Protocol Version 4(TCP/IPv4)

and then click

Properties.

Then

click on

Obtain an IP address automatically.

Page 8 / 13

2. I am not sure what type of Internet Account Type I have for my Cable/DSL connection.

How do I find out?

Contact your Internet Service Provider's (ISP) support service for the correct information.

3. I configured my router with my ISP settings, but I can not get onto the Internet.

What

should I do?

1. Verify that you can get onto the Internet with a direct connection into your modem.

2. Contact your ISP and verify all the information that you have in regards to your Internet

connection settings is correct.

3. Power cycle your modem and router.

Unplug the power to the modem and router.

Wait

30 seconds, and then reconnect the power to the modem.

Wait for the modem to fully

boot up, and then reconnect the power to the router.

4. All the settings are correct, but I can not make a wireless connection to the Router.

What

should I do?

1. Make sure that the WLAN switch on the back of the router is set to on.

2. Double check that the WLAN light on the Router is lit.

3. Power cycle the TEW-639GR.

Unplug the power to the TEW-639GR.

Wait 15 seconds,

then plug the power back in to the TEW-639GR.

4. Contact the manufacturer of your wireless network adapter and make sure the wireless

network adapter is configured with the proper SSID.

The default SSID of the TEW-639GR

is

TRENDnet639.

5. When I connect a computer to the router's LAN port, I am not getting Gigabit speeds.

What should I do?

1.

Make sure that you have a Gigabit Ethernet adapter installed.

2. Make sure to use a Cat-5e or Cat 6 Ethernet cable.

Some CAT-5 cables are not rated to

run in Gigabit.

If you still encounter problems or have any questions regarding the

TEW-639GR,

please contact

TRENDnet's Technical Support Department.

6

1.

Go into the

Control Panel

, double-click the

Network

Connections

icon and then right-click the

Local

Area Connection

icon and then click

Properties

.

Windows XP/2000

2.

Click

Internet Protocol (TCP/IP)

and then click

Properties.

Then click on

Obtain an IP address

automatically.

Page 9 / 13

Page 10 / 13

Rate

Popular TRENDnet Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share