TRENDnet TEW-434APB Router Manual PDF (Setup & Configuration Guide)

Page 6 / 13 Scroll up to view Page 1 - 5

English

4

Using the TEW-434APB with the TPE-101I

1.

Connect the

Power Cord

to the

AC Power Adapter.

2.

Connect the

AC Power Adapter

to

the

DC 48V IN

connector on the

TPE-101I.

Then connect the

Power Cord

to an outlet.

3.

Connect a CAT-5 cable from a

switch to the TPE-101I's

DATA IN

port.

4.

Connect a CAT-5 cable from the

TEW-434APB's

LAN

port to the

TPE-101I's

POE OUT

port

5.

Verify that the following panel lights

are on:

WLAN

and

LAN

.

Please

refer to step 3 in the Hardware

Installation.

Page 7 / 13

English

5

4. Configure the Access Point

Note: It is recommended that you configure the Access Point from a wired

computer.

Before the Access Point can be configured, a Static IP address

must be assigned to your computer's network adapter in the subnet of

192.168.1.x.

Since the Access Point's default IP address is 192.168.1.100,

make sure no other network devices are assigned an IP address of

192.168.1.100.

(Refer to the Troubleshooting section on how to configure

TCP/IP settings on your PC)

2.

Enter User name and Password,

and then click

OK

. By default,

User name:

admin

Password:

admin

1.

Open your web browser, type

http://192.168.1.100

in the

Address bar, and press

Enter

.

3.

Click

Wizard

.

Page 8 / 13

English

6

5.

Enter a new password for your

Access Point, verify the new

password, and then click

Next.

(If a

new password is not entered, the

default password

admin

will be

used.

4.

Click

6.

Enter a SSID for your Access

Point and then click

Page 9 / 13

English

7

8.

Click

Restart

.

7.

Enable Encryption if needed and

then click

9.

Click

Close.

Your installation is now complete.

For detailed information regarding the TEW-434APB's configuration and

advanced settings, please refer to the Troubleshooting section, User's Guide

CD-ROM, or TRENDnet's website at http://www.trendnet.com.

Page 10 / 13

8

Troubleshooting

Q1:

How do I configure TCP/IP settings on my computer?

1.

Go into the

Control Panel

and double-

click the

Network Connections

icon,

right-click the

Local Area Connection

icon and then click

Properties

.

2.

Click

Internet Protocol (TCP/IP)

and

then click

Properties

.

Then click on

Use the following IP address

, and

make sure you assign your network

adapter an IP address in the subnet of

192.168.1.x.

Q2:

A2:

Q3:

A3:

If my network's IP is different than the Access Point's range, what should I

do?

You should still configure the Access Point first. After all the settings are

applied, go to the Access Point's configuration page, click on TCP/IP settings and

change the IP address of the Access Point to match your network's IP.

I typed http://192.168.1.100 in my Internet Browser's Address Bar, but an

error message says “The page cannot be displayed.” How can I get into the

TEW-434APB's web configuration page?

First, check your hardware settings again by following the instructions in

section 2.

Second, make sure the LAN and WLAN lights are lit.

Third, make sure

the TCP/IP settings are configured properly (see Q1).

Fourth, since the Access

Point's default IP address is 192.168.1.100, make sure that no other network

devices are assigned an IP address of 192.168.1.100.

Rate

Popular TRENDnet Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share