Page 81 / 110
Scroll up to view Page 76 - 80
TD-W8960NB
300Mbps Wireless N ADSL2+ Modem Router User Guide
Figure 4-78
3.
WPA-PSK
WPA-PSK requires a shared key and does not use a separate server for authentication. PSK keys
can be ASCII or Hex type.
Figure 4-79
¾
WPA Pre-Shared Key:
Enter the key shared by the Router and your other network devices. It
must have 8-63 ASCII characters or 64 Hexadecimal digits.
¾
Click here to display:
Click it to show you the WPA Pre-Shared Key.
74
Page 82 / 110
TD-W8960NB
300Mbps Wireless N ADSL2+ Modem Router User Guide
Configure WPA-PSK settings
1. Select
WPA-PSK
. The menu will change to offer the appropriate settings as the picture show
above.
2.
WPA-PSK requires a shared key. Type the key in the space provided. PSK keys can be ASCII
or Hex type.
3.
Change the Group Key Interval as desired or use the default setting.
4. Click
Save/Apply
to save the new configuration.
Figure 4-80
)
Note:
If you click the option “Click here to display”, the Figure 4-81 will pop-up, and it shows the
password you have set.
Figure 4-81
4.
WPA2
To configure WPA2 settings, select the WPA2 option from the drop-down list. The menu will
change to offer the appropriate settings. The steps of these settings are similar to WPA settings.
75
Page 83 / 110
TD-W8960NB
300Mbps Wireless N ADSL2+ Modem Router User Guide
Figure 4-82
¾
WPA2 Preauthentication:
Select Enable from the drop-down list, Stations will authenticate
with the AP during the scanning process, and once association is required, the station has
been already authenticated.
¾
Network Re-auth Interval:
Enter a value in seconds as the frequency interval to enable
periodic Network Re-authentication function, while leave it blank or enter “0” to disable it.
5.
WPA2-PSK
To configure WPA2-PSK settings, select the WPA2-PSK option from the drop-down list. The menu
will change to offer the appropriate settings. WPA2-PSK requires a shared key and does not use a
separate server for authentication. PSK keys can be ASCII or Hex type.
Figure 4-83
76
Page 84 / 110
TD-W8960NB
300Mbps Wireless N ADSL2+ Modem Router User Guide
6.
Mixed WPA2/WPA
To configure Mixed WPA2/WPA settings, select the Mixed WPA2/WPA option from the drop-down
list. The menu will change to offer the appropriate settings. The steps to these settings are similar
to those for WPA-PSK.
Figure 4-84
7.
Mixed WPA2/WPA-PSK
To configure Mixed WPA2/WPA-PSK settings, select the Mixed WPA2/WPA-PSK option from the
drop-down list. The menu will change to offer the appropriate settings. The steps of this setting are
the same with WPA-PSK.
Figure 4-85
77
Page 85 / 110
TD-W8960NB
300Mbps Wireless N ADSL2+ Modem Router User Guide
4.5.3 MAC Filter
Choose “
Wireless
”
Æ
”
MAC Filter
”, you will see the screen of
Wireless--MAC
Filter
settings
shown as below.
Figure 4-86
Wireless access can be filtered by using the MAC addresses of the wireless devices transmitting
within your network’s RADIUS. To filter wireless users by MAC Address, either permitting or
blocking access. If you do not wish to filter users by MAC Address, select Disabled.
¾
Disabled:
Select this option to disable MAC Filter function.
¾
Allow:
Select this option to enable MAC Filter function that allow wireless access by the
devices listed on this screen.
¾
Deny:
Select this option to enable MAC Filter function that block wireless access from the
devices listed on this screen.
¾
Add:
Click this button to add the MAC Address.
¾
Remove:
Select the item of the MAC Address and click this button to remove it.
When you click the
Add
button, the pop-up picture shown below, and then you can type the MAC
Address in the
MAC Address
field.
)
Note:
The form of MAC Address must be “
xx:xx:xx:xx:xx:xx
”, like “
00:13:0A:55:FF:09
”.
Figure 4-87
When you finished making changes to the MAC Filter List screen, click
Save/Apply
to save the
changes.
78
19216811.live