TD-W8950ND

150Mbps Wireless Lite N ADSL2+ Modem Router User Guide

Figure 4-18

Click the Next button to enter the next step as shown in Figure 4-19. Click Save to complete the

configuration.

Figure 4-19

¾

IP over ATM (IPoA)

If you select the protocol of IP over ATM (IPoA), you will see the Figure 4-20. Enter the parameters

provided by your ISP.

29

TD-W8950ND

150Mbps Wireless Lite N ADSL2+ Modem Router User Guide

Figure 4-20

±

WAN IP Address: Enter the IP Address provided by your ISP.

±

WAN Subnet Mask: Enter the subnet mask provide by your ISP.

±

Use the following default gateway: Check this radio button then you can choose Use IP

Address or Use WAN Interface. If you have any problems, please ask your ISP for the

information.

±

Use the following DNS server addresses: Check this radio button then you can enter the

primary DNS server and secondary DNS server. If you have any problems, please ask your

ISP for the information.

)

Note:

1)

DHCP is not supported in IPoA mode.

2)

Changing the default gateway or the DNS will affect the whole system. Configuring them with

static values will disable the automatic assignment from other WAN connection.

Click Next in Figure 4-20, and then you will see the Figure 4-21.

Figure 4-21

Check or uncheck the Enable WAN Service box according to your needs. Click the Next button to

enter the next step as shown in Figure 4-22, and click Save to complete the configuration.

30

TD-W8950ND

150Mbps Wireless Lite N ADSL2+ Modem Router User Guide

Figure 4-22

¾

Bridging

If you select the Bridging protocol, you will see the Figure 4-23. Click the Next button.

Figure 4-23

Then you will see the Figure 4-24. Click Save to complete the configuration

31

TD-W8950ND

150Mbps Wireless Lite N ADSL2+ Modem Router User Guide

Figure 4-24

)

Note:

After completing any setup, the new setup must be saved and the Router must be restarted for the

configuration to go into effect. Please click the Save/Reboot button to restart as shown in Figure

4-25.

Figure 4-25

)

Note:

All of the above setup is under windows XP OS.

4.5.2 LAN

Choose “Advanced Setup

→

LAN” menu, and you can see and configure the Local Area Network

(LAN) parameters in the screen as shown in Figure 4-26.

32

TD-W8950ND

150Mbps Wireless Lite N ADSL2+ Modem Router User Guide

Figure 4-26

¾

IP Address - Enter an IP address for the Router. Then you can access the Web-based Utility

via this IP address. The default setting is 192.168.1.1.

¾

Subnet Mask - An address code that determines the size of the network. Normally use

255.255.255.0 as the subnet mask.

)

Note:

1)

If you change the IP Address of LAN, you must use the new IP Address to log in the

Router.

2)

If the new LAN IP Address you set is not in the same subnet, the IP Address pool of the

DHCP server will change accordingly at the same time

，

while the Virtual Server and DMZ

Host will not take effect until they are re-configured.

¾

Enable SPI Firewall: Check this box to enable the SPI Firewall function. The default value is

disabled.

¾

Enable IGMP Snooping: By default this option is enabled. With this function enabled, the

Router can listen to the IGMP messages transmitted from the LAN to the WAN, and track the

IGMP messages and the registered port.

¾

Disable/Enable DHCP Server - Disable or Enable the DHCP server. DHCP stands for

Dynamic Host Configuration Protocol. The DHCP Server will automatically assign dynamic IP

addresses to the computers on the network. If you disable the Server, you must have another

DHCP server within your network or else you must configure the computer manually. The

following options are available only when DHCP Server is enabled.

z

Start IP Address - Specify an IP address for the DHCP Server to start with when

assigning IP addresses. 192.168.1.100 is the default start address

33