Page 26 / 94
Scroll up to view Page 21 - 25
TD-W8950ND
150Mbps Wireless Lite N ADSL2+ Modem Router User Guide
The QSS Configuration Screen of Wireless Adapter
II. By PIN
If the new device supports Wi-Fi Protected Setup and the PIN method, you can add it to the
network by PIN with the following two methods.
Method One: Enter the PIN into my Router
Step 1: Keep the default QSS Status as Enabled and click the Add device button in
Figure 4-2
,
then the following screen will appear.
Step 2: Choose
Enter the new device's PIN
and enter the PIN code of the wireless adapter in
the field behind PIN in the above figure. Then click Connect.
)
Note:
The PIN code of the adapter is always displayed on the QSS configuration screen
Step 3: For the configuration of the wireless adapter, please
choose Enter a PIN into my
access point or a registrar
in the configuration utility of the QSS as below, and click
Next.
19
Page 27 / 94
TD-W8950ND
150Mbps Wireless Lite N ADSL2+ Modem Router User Guide
The QSS Configuration Screen of Wireless Adapter
)
Note:
In this example, the default PIN code of this adapter is 16952898 as the above figure shown.
Method Two: Enter the PIN from my Router
Step 1: Get the Current PIN code of the Router in
Figure 4-2
(each Router has its unique PIN
code. Here takes the PIN code 12345670 of this Router for example).
Step 2: For the configuration of the wireless adapter, please choose Enter a PIN from my access
point in the configuration utility of the QSS as below, and enter the PIN code of the Router
into the field behind Access Point PIN. Then click
Next
.
The QSS Configuration Screen of Wireless Adapter
20
Page 28 / 94
TD-W8950ND
150Mbps Wireless Lite N ADSL2+ Modem Router User Guide
)
Note:
PIN code of the Router can be found in its label or the QSS configuration screen as
ill see the following screen when the new device successfully connected to the
The default
Figure 4-2
.
c).
You w
network.
)
Note:
tus LED on the Router will light green all the time if the device has been successfully
not be configured if the Wireless Function of the Router is disabled.
you can see the submenus as shown in Figure 4-7
1
）
The sta
added to the network.
2
）
The QSS function can
Please make sure the Wireless Function is enabled before configuring the QSS.
4.5 Advanced Setup
Choose “Advanced Setup”, and
Figure 4-7
21
Page 29 / 94
TD-W8950ND
150Mbps Wireless Lite N ADSL2+ Modem Router User Guide
4.5.1 WAN
Choose “Advanced Setup”
Æ
”WAN”, and you will see the page of Wide Area Network (WAN)
Setup as shown Figure 4-8
Figure 4-8
e WAN setup page. Click the Add button or choose the appropriate
PVC according to your need. Then you will enter the page of ATM PVC Configuration as shown in
Figure 4-9.
There are 4 PVC links in th
Figure 4-9
Enter VPI/VCI value and service category provided by your ISP. Click Next to enter the next step.
You will see the Figure 4-10.
22
Page 30 / 94
TD-W8950ND
150Mbps Wireless Lite N ADSL2+ Modem Router User Guide
Figure 4-10
After choosing the proper protocol, enter the correct parameters supported by your ISP. Enable
the configurations, and then you will go to the Internet.
)
Note:
The type of network protocol selected may be different in different areas. There are five types, so
you should ask your ISP to acquire the Connection Type and Encapsulation Mode.
¾
PPP over ATM (PPPoA)
If you select the protocol of PPP over ATM (PPPoA), you will see the Figure 4-11.
23
19216811.live