1. Home
    2. /
  2. Manuals
    3. /
  3. TP-Link
    4. /
  4. TD-W8950ND
    5. /
  5. 7
Page 31 / 94 Scroll up to view Page 26 - 30
TD-W8950ND
150Mbps Wireless Lite N ADSL2+ Modem Router User Guide
Figure 4-11
±
PPP Username: Enter your username for your PPPoA connection to identify and verify your
account to the ISP.
±
PPP Password: Enter your password for your PPPoA connection.
±
Authentication Method: Choose a method of authentication, AUTO, PAP, CHAP, or
MSCHAP.
±
MTU: The default MTU value is 1480 Bytes. It is not recommended that you change the
default value unless required by your ISP. The value should be between 512 and 1492.
±
Enable Fullcone NAT: Check this box to enable the Fullcone NAT function. The default value
is disabled.
±
Dial on demand: If you check this box, the Internet connection can be terminated
automatically after a specified inactivity period (Inactivity Timeout) and be re-established
when you attempt to access the Internet again. The default value of Inactivity Timeout is 15.
The value should be between 1 and 4320.
±
PPP IP extension: If this box is checked, the IP address obtained by the Router will be
assigned to the computer, and the NAT and Firewall will be disabled.
±
Use Static IP Address: Check this box to use the static IP address to dial. The default value is
disabled.
±
Enable PPP Debug Mode: Check this box to enable the debug mode. The default value is
disabled.
Click Next button in Figure 4-11, and then you will see Figure 4-12. Check or uncheck the Enable
WAN Service box according to your needs.
24
Page 32 / 94
TD-W8950ND
150Mbps Wireless Lite N ADSL2+ Modem Router User Guide
Figure 4-12
Click the Next button to enter the next step as shown in Figure 4-13. Click Save to complete the
configuration.
Figure 4-13
¾
PPP over Ethernet (PPPoE)
If you select the protocol of PPP over Ethernet (PPPoE), you will see the Figure 4-14.
25
Page 33 / 94
TD-W8950ND
150Mbps Wireless Lite N ADSL2+ Modem Router User Guide
Figure 4-14
±
PPP Username: Enter your username for your PPPoE connection to identify and verify your
account to the ISP.
±
PPP Password: Enter your password for your PPPoE connection.
±
PPPoE Service Name: Enter a name for the PPPoE connection for recognition.
±
Authentication Method: Choose a method of authentication, AUTO, PAP, CHAP, or
MSCHAP.
±
MTU: The default MTU value is 1480 Bytes. It is not recommended that you change the
default value unless required by your ISP. The value should be between 512 and 1492.
±
Enable Fullcone NAT: Check this box to enable the Fullcone NAT function. The default value
is disabled.
±
Dial on demand: If you check this box, the Internet connection can be terminated
automatically after a specified inactivity period (Inactivity Timeout) and be re-established
when you attempt to access the Internet again. The default value of Inactivity Timeout is 30.
The value should be between 1 and 4320.
±
PPP IP extension: If this box is checked, the IP address obtained by the Router will be
assigned to the computer, and the NAT and Firewall will be disabled.
±
Use Static IP Address: Check this box to use the static IP address to dial. The default value is
disabled.
±
Enable PPP Debug Mode: Check this box to enable the debug mode. The default value is
disabled.
±
Bridge PPPoE Frames Between WAN and Local Ports: If you check this box, you can
establish dial-up connection in this Router or on the PC. By default, the checkbox is selected.
Click Next button in Figure 4-14, and then you will Figure 4-15. Check or uncheck the Enable WAN
Service box according to your needs.
26
Page 34 / 94
TD-W8950ND
150Mbps Wireless Lite N ADSL2+ Modem Router User Guide
Figure 4-15
Click the Next button to enter the next step as shown in Figure 4-16. Click Save to complete the
configuration.
Figure 4-16
¾
MAC Encapsulation Routing (MER)
If you select the protocol of MAC Encapsulation Routing (MER), you will see the page as shown in
Figure 4-17.
27
Page 35 / 94
TD-W8950ND
150Mbps Wireless Lite N ADSL2+ Modem Router User Guide
Figure 4-17
±
Obtain an IP address automatically: This radio button is checked by default. You can obtain
the IP address automatically.
±
Use the following IP address and gateway: Check this radio button to enter the information
provided by your ISP to configure the WAN IP settings.
±
Obtain DNS server addresses automatically: This radio button is checked by default. It’s
recommended that you keep the default settings to allow the Router to obtain the default DNS
server addresses automatically.
±
Use the following DNS server addresses: Check this radio button then you can enter the
primary DNS server and secondary DNS server. This is not recommended by default.
)
Note:
1)
DHCP can be enabled for PVC in MER mode as WAN interface if "Obtain an IP address
automatically" is chosen.
2)
Changing the default gateway or the DNS will affect the whole system. Configuring them with
static values will disable the automatic assignment from DHCP or other WAN connection.
3)
If you configure static default gateway over this PVC in MER mode, you must enter the IP
address of the remote gateway in the "Use IP address". The "Use WAN interface" is optional.
Click Next button in Figure 4-17, and then you will see the Figure 4-18. Check or uncheck the
Enable WAN Service box according to your needs.
28

Rate

4.5 / 5 based on 2 votes.

Popular TP-Link Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top