TD-W8151N

150Mbps Wireless N ADSL2+ Modem Router User Guide

29

Figure 4-19

Method One:

Step 1:

Press the QSS button on the front panel of the Router or click

Start QSS

button in

Figure 4-19.

Step 2:

Press and hold the QSS button of the adapter directly for 2 or 3 seconds.

Step 3:

Wait for a while until the next screen appears. Click

Finish

to complete the QSS

configuration.

The QSS Configuration Screen of Wireless Adapter

Method Two:

Step 1:

Press the QSS button on the front panel of the Router or click

Start QSS

button in

Figure 4-19.

TD-W8151N

150Mbps Wireless N ADSL2+ Modem Router User Guide

30

Step 2: For the configuration of the wireless adapter, please choose “

Push the button on

my access point

”

in the

configuration utility of the QSS as below, and click

Next

.

The QSS Configuration Screen of Wireless Adapter

Step 3:

Wait for a while until the next screen appears. Click

Finish

to complete the QSS

configuration.

The QSS Configuration Screen of Wireless Adapter

TD-W8151N

150Mbps Wireless N ADSL2+ Modem Router User Guide

31

2)

PIN code

If the wireless adapter supports Wi-Fi Protected Setup and the PIN method, you can add it to

the network by PIN with the following two methods. Click

PIN code

, you will see the screen as

shown below.

Figure 4-20

Method One:

Enter the PIN into my Router

Step 1:

For the configuration of the wireless adapter, please choose “

Enter a PIN into my

access point or a registrar

”

in the

configuration utility of the QSS, and get the PIN

code on the screen as below, then click

Next.

The QSS Configuration Screen of Wireless Adapter

Step 2: For the Router, keep

PIN code

selected and enter the PIN code of the wireless

adapter in the field after

enrollee

PIN code

as shown below. Then click

Start QSS

.

TD-W8151N

150Mbps Wireless N ADSL2+ Modem Router User Guide

32

Figure 4-21

Method Two:

Enter the PIN from my Router

Step 1:

Get the Current PIN code of the Router from

AP self PIN code

in Figure 4-21 (each

Router has its unique PIN code. Here takes the PIN code 55924054 of this Router

for example).

Step 2:

For the configuration of the wireless adapter, please choose “

Enter a PIN from my

access point

”

in the

configuration utility of the QSS as below, and enter the PIN

code of the Router into the field after “

Access Point PIN

”. Then click

Next

.

00745659

The QSS Configuration Screen of Wireless Adapter

)

Note:

The default PIN code of the Router can be found in its label or the QSS configuration screen

as Figure 4-21.

•

QSS progress:

Show the current QSS progress.

TD-W8151N

150Mbps Wireless N ADSL2+ Modem Router User Guide

33

•

SSID:

Wireless network name shared among all points in a wireless network. The SSID

must be identical for all devices in the wireless network. It is case-sensitive and must not

exceed 32 characters (use any of the characters on the keyboard). Make sure this setting

is the same for all stations in your wireless network. Type the desired SSID in the space

provided.

•

Authentication Type:

Select an authentication type from the drop-down list, which

allows you to configure security features of the wireless LAN interface. Options available

are: Disabled, WEP-64Bits, WEP-128Bits, WPA-PSK, WPA2-PSK, and WPA-PSK/

WPA2-PSK.

¾

WDS Settings:

Select On/Off to enable/disable WDS. With this function enabled, the Router

can bridge two or more WLANs.

•

MAC Address:

Enter the MAC Address you wish to bridge in the field.

¾

Wireless MAC Address Filter:

Wireless access can be filtered by using the MAC addresses

of the wireless devices transmitting within your network’s RADIUS.

•

Active:

If you wish to filter users by MAC Address, select “Activated”, and “Deactived” for

don’t.

•

Action:

To filter wireless users by MAC Address, select “Allow Association” or “Deny

Association” the follow Wireless LAN station(s) association.

•

MAC Address:

Enter the MAC Address you wish to filter in the field.

4.4

Advanced Setup

Choose “

Advanced Setup

”, you can see the next submenus:

Figure 4-22

Click any of them, and you will be able to configure the corresponding function.

4.4.1 Firewall

Choose “

Advanced Setup

→

Firewall

” menu, and you will see the next screen (shown in Figure

4-23).

Figure 4-23