TD-W8151N

150Mbps Wireless N ADSL2+ Modem Router User Guide

14

Figure 3-12

)

Note:

If the Access Point is activated, the wireless function will be available even without the external

antenna because of an additional printed antenna. To adopt the wireless security protection

measures, please refer to section 4.3.3.

Step 6:

Click

NEXT

to save the current settings.

Figure 3-13

Step 7:

Click

CLOSE

to complete.

Figure 3-14

TD-W8151N

150Mbps Wireless N ADSL2+ Modem Router User Guide

15

Chapter 4 Software Configuration

This User Guide recommends using the “Quick Installation Guide” for first-time installation. For

advanced users, if you want to know more about this device and make use of its functions

adequately, maybe you will get help from this chapter to configure the advanced settings through

the Web-based Utility.

After your successful login, you can configure and manage the device. There are main menus on

the top of the Web-based Utility; submenus will be available after you click one of the main menus.

On the center of the Web-based Utility, there are the detailed configurations or status information.

To apply any settings you have altered on the page, please click the

SAVE

button.

4.1

Status

Choose “

Status

”, you can see the next submenus:

Device Info

,

System Log

and

Statistics

.

Click any of them, and you will be able to configure the corresponding function.

Figure 4-1

Choose “

Status

→

Device Info

” menu, and you will be able to view the device information,

including LAN, WAN and ADSL. The information will vary depending on the settings of the Router

configured on the Interface Setup screen.

TD-W8151N

150Mbps Wireless N ADSL2+ Modem Router User Guide

16

Figure 4-2

)

Note:

Click the other submenus

System Log

or

Statistics

in Figure 4-2, and you will be able to view the

system log and traffic statistics about the Router.

4.2

Quick Start

Please refer to

"3.2: Login"

.

4.3

Interface Setup

Choose “

Interface Setup

”, you can see the next submenus:

Internet

and

LAN

and

Wireless

.

Figure 4-3

Click any of them, and you will be able to configure the corresponding function.

TD-W8151N

150Mbps Wireless N ADSL2+ Modem Router User Guide

17

4.3.1 Internet

Choose “

Interface Setup

→

Internet

” menu, you can configure the parameters for WAN ports in

the next screen (shown in Figure 4-4).

Figure 4-4

¾

ATM VC:

ATM settings are used to connect to your ISP. Your ISP provides VPI (Virtual Path

Identifier), VCI (Virtual Channel Identifier) settings to you. In this Device, you can totally setup

8 VCs on different encapsulations, if you apply 8 different virtual circuits from your ISP. You

need to activate the VC to take effect. For PVCs management, you can use ATM QoS to

setup each PVC traffic line's priority.

•

Virtual Circuit:

Select the VC number you want to setup, PVC0~PVC7.

•

Status:

If you want to use a designed VC, you should activate it.

•

VPI:

Identifies the virtual path between endpoints in an ATM network. The valid range is

from 0 to 255. Please input the value provided by your ISP.

•

VCI:

Identifies the virtual channel endpoints in an ATM network. The valid range is from

32 to 65535 (1 to 31 is reserved for well-known protocols). Please input the value

provided by your ISP.

•

PVCs Summary:

Click the button, and you can view the summary information about the

PVCs.

•

ATM QoS:

Select the Quality of Service types for this Virtual Circuit, including CBR

(Constant Bit Rate), UBR (Unspecified Bit Rate) and VBR (Variable Bit Rate). These QoS

types are all controlled by the parameters specified below, including PCR (Peak Cell

Rate), SCR (Sustained Cell Rate) and MBS (Maximum Burst Size), please configure

them according your needs.

¾

Encapsulation:

There are four connection types: Dynamic IP Address, Static IP Address,

TD-W8151N

150Mbps Wireless N ADSL2+ Modem Router User Guide

18

PPPoA/PPPoE and Bridge Mode. Please choose the designed type that you want to use.

After that, you should follow the configuration below to proceed.

1)

Dynamic IP Address

Select this option if your ISP provides you an IP address automatically. This option is typically

used for Cable services. Please enter the Dynamic IP information accordingly.

Figure 4-5

¾

Encapsulation:

Select the encapsulation mode for the Dynamic IP Address, you can leave it

default.

¾

NAT:

Select this option to Enable/Disable the NAT (Network Address Translation) function for

this VC. The NAT function can be activated or deactivated per PVC basis.

¾

Default Route:

If enable this function, the current PVC will be considered as the default

gateway to internet from this device.

¾

TCP MTU Option:

Enter the TCP MTU as your desire.

¾

Dynamic Route:

Select this option to specify the RIP (Routing Information protocol) version

for WAN interface, including

RIP1

,

RIP2-B

and

RIP2-M

. RIP2-B and RIP2-M are both sent in

RIP2 format, the difference is that RIP2-M using Multicast, while RIP2-B using Broadcast

format.

•

Direction:

Select this option to specify the RIP direction.

None

is for disabling the RIP

function.

Both

means the ADSL Router will periodically send routing information and

accept routing information, and then incorporate them into routing table.

IN Only

means

the ADLS Router will only accept but will not send RIP packet.

OUT Only

means the

ADLS Router will only send but will not accept RIP packet.

¾

Multicast:

Select IGMP version, or disable the function. IGMP (Internet Group Multicast

Protocol) is a session-layer protocol used to establish membership in a multicast group. The

ADSL ATU-R supports both IGMP version 1 (

IGMP v1

) and

IGMP v2

. Select “Disabled” to

disable it.

¾

MAC Spoofing:

Enable

the MAC Spoofing, and enter a MAC address to configure the WAN

port. It makes your inside network appear as a device with this MAC address to the outside

world.