Page 36 / 129
Scroll up to view Page 31 - 35
TD-VG3631
300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide
27
¾
Authentication Method:
Select the
Authentication Method
from the drop-down list, the
default method is
AUTO_AUTH
, and you can leave it as a default setting.
¾
Choose the right connection type according to your needs:
For PPPoE connection, you
can select
Connect on demand
or
Connect automatically
or
Connect manually
. Connect
on demand is dependent on the traffic. If there is no traffic (or
Idle
) for a pre-specified period
of time), the connection will tear down automatically. And once there is traffic send or receive,
the connection will be automatically on.
Click
Advanced
, advanced selections for WAN Service Setup can be shown.
¾
Service Name/Server Name:
Enter the Service Name and Server Name if it was provided by
your ISP. You can leave them blank, if the ISP doesn’t provide them.
4.4.1.4 PPPoA
If your ISP provides a
PPPoA
connection and you need to use an ATM Interface, choose
PPPoA
in the drop-down list, and then the screen will be displayed as below.
The configuration is similar to
PPPoE
. Please refer to the section
4.4.14 PPPoE
to configure this
part.
Page 37 / 129
TD-VG3631
300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide
28
Figure 4-7
4.4.1.5 IPoA
If your ISP provides an IPoA connection, select
IPoA
option for the
WAN service type
on the
screen.
Page 38 / 129
TD-VG3631
300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide
29
Figure 4-8
¾
IP Address/Subnet Mask:
Enter the IP Address and Subnet Mask provided by ISP. If you
forget, you can ask your ISP.
¾
DNS Server/Secondary DNS Server:
Type in your preferred DNS server.
¾
Default Gateway:
select a WAN Interface from the drop-down list as the IPv4 default
gateway.
4.4.1.6 Bridge
If you select this type of connection, the modem can be configured to act as a bridging device
between your LAN and your ISP. Bridges are devices that enable two or more networks to
communicate as if they are two segments of the same physical LAN.
Page 39 / 129
TD-VG3631
300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide
30
Figure 4-9
)
Note:
After you finish the Internet configuration, please click
Save
to make the settings take effect.
4.4.2 EWAN
Choose “
Network
”
Æ
“
EWAN
”, and you will see the Ethernet WAN Interface screen similar to
Figure 4-10. There are three different configurations for the connection types, which are Dynamic
IP, Static IP and PPPoE. You can select the corresponding types according to your needs.
)
Note:
1)
EWAN and DSL interface can not be used concurrently. If the EWAN Interface had configured,
you cannot configure any other WAN service over the DSL Interface until the EWAN Interface
is deleted.
2) If EWAN function is be enabled, LAN4/WAN port of the Modem Router changes to be WAN
port which can be connected to the cable, VDSL or Fiber modem.
Page 40 / 129
TD-VG3631
300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide
31
Figure 4-10
4.4.2.1 Dynamic IP
Select this option, the Modem Router will be able to obtain IP network information dynamically
from a DHCP server provided by your ISP (as shown Figure 4-10). The next configuration is
similar to
Dynamic IP
over ATM interface
(see section
4.4.1.2 Dynamic IP
)
4.4.2.2 Static IP
Select this option if your ISP provides static IP information to you and you want to use an
Ethernet
Interface. You should set static IP address, IP subnet mask, gateway address, DNS Server and
Secondary DNS Server in the screen below. The next configuration is similar to
Static IP
for WAN
Settings (see section
4.4.1.1 Static IP
)
19216811.live