TD-VG3631

300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide

42

Figure 4-23

To add a

vendor class:

1.

Click the

Add New

button. Then Figure 4-24 will pop up.

2.

Enter parameters for the vendor class.

Click the

Save

button.

Figure 4-24

To modify or delete an existing entry:

4.

Click the

Edit

in the entry you want to modify. If you want to delete the entry, click the

Delete

.

5.

Modify the information.

6.

Click the

Save

button.

Click the

Enable/Disable Selected

button to make selected entries enabled/disabled.

Click the

Delete Selected

button to selected entries.

TD-VG3631

300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide

43

4.6 Wireless

Choose “

Wireless

”, there are six submenus to configure Wireless LAN settings. Click any of them,

and you will be able to configure the corresponding function. The detailed explanations for each

submenu are provided below.

4.6.1 Basic Settings

Choose “

Wireless

”

Æ

”

Basic

”, you will see the screen of

Wireless--Basic

settings shown as below.

The basic settings for wireless networking are set on this screen.

Figure 4-25

This page allows you to configure basic features of the wireless LAN interface. You can enable or

disable the wireless LAN interface, hide the network from active scans, set the wireless network

name (also known as SSID) and restrict the channel set based on Region requirements.

¾

SSID:

Wireless network name shared among all points in a wireless network. The SSID must

be identical for all devices in the wireless network. It is case-sensitive and must not exceed 32

characters (use any of the characters on the keyboard). Make sure this setting is the same for

all stations in your wireless network. Type the desired SSID in the space provided.

¾

Mode

:

Select the desired mode.

11b only:

Select if all of your wireless clients are 802.11b.

11g only:

Select if all of your wireless clients are 802.11g.

11n only:

Select only if all of your wireless clients are 802.11n.

TD-VG3631

300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide

44

11bg mixed:

Select if you are using both 802.11b and 802.11g wireless clients.

11bgn mixed:

Select if you are using a mix of 802.11b, 11g, and 11n wireless clients.

Select the desired wireless mode. When 802.11g mode is selected, only 802.11g wireless

stations can be connected to the Modem Router. When 802.11n mode is selected, only

802.11n wireless stations can connect to the Modem Router. It is strongly recommended that

you set the Mode to

802.11b&g&n

, and all of 802.11b, 802.11g, and 802.11n wireless

stations can connect to the Modem Router.

¾

Channel:

Select the channel you want to use from the drop-down List of Channel. This field

determines which operating frequency will be used. It is not necessary to change the wireless

channel unless you notice interference problems with another nearby access point.

¾

Channel Width:

Select the channel width from the drop-down list

.

The default setting is

automatic, which can adjust the channel width for your clients automatically.

)

Note:

If

11b only

,

11g only

, or

11bg mixed

is selected in the

Mode

field, the

Channel Width

selecting

field will turn grey and the value will become 20M, which is unable to be changed.

¾

Enable Wireless Router Radio:

If you want to use wireless features, you must select “Enable

Wireless

Router Radio”. If you deselect “Enable Wireless Router Radio” option, all the Wireless

settings below will be disabled.

¾

Enable SSID Broadcast:

When wireless clients survey the local area for wireless networks to

associate with, they will detect the SSID broadcast by the Modem Router. If you select the

Enable SSID Broadcast

checkbox, the Wireless Router will broadcast its name (SSID) on the

air.

¾

Enable WDS:

Check this box to enable WDS. With this function, the Modem Router can bridge

two or more Wlans. If this checkbox is selected, you will have to set the following parameters

as shown in the figure below. Make sure the following settings are correct.

¾

SSID (to be bridged):

The SSID of the AP your Modem Router is going to connect to as a

client. You can also use the search function to select the SSID to join.

¾

BSSID (to be bridged):

The BSSID of the AP your Modem Router is going to connect to as

a client. You can also use the search function to select the BSSID to join.

¾

Scan:

Click this button, you can search the AP which runs in the current channel.

¾

Key type

: This option should be chosen according to the AP's security configuration. It is

recommended that the security type is the same as your AP's security type

TD-VG3631

300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide

45

¾

WEP Index:

This option should be chosen if the key type is WEP(ASCII) or WEP(HEX). It

indicates the index of the WEP key.

¾

Auth Type:

This option should be chosen if the key type is WEP(ASCII) or WEP(HEX). It

indicates the authorization type of the Root AP.

¾

Password

:

If the AP your Modem Router is going to connect needs password, you need to

fill the password in this blank.

Click

Save

to save your settings.

4.6.2 WPS Settings

This section will guide you to add a new wireless device to an existing network quickly by

WPS

(also called

QSS

)

function.

a).

Choose menu “

WPS Settings

”, and you will see the next screen (shown in Figure 4-26 ).

Figure 4-26

¾

WPS:

Enable or disable the WPS function here.

¾

Current PIN:

The current value of the Modem Router's PIN is displayed here. The default

PIN of the Modem Router can be found in the label or User Guide.

¾

Restore PIN:

Restore the PIN of the Modem Router to its default.

¾

Gen New PIN:

Click this button, and then you can get a new random value for the Modem

Router's PIN. You can ensure the network security by generating a new PIN.

¾

Add device:

You can add a new device to the existing network manually by clicking this

button.

b).

To add a new device:

If the wireless adapter supports Wi-Fi Protected Setup (WPS), you can establish a wireless

connection between wireless adapter and Modem Router using either Push Button Configuration

(PBC) method or PIN method.

)

Note:

To build a successful connection by WPS, you should also do the corresponding configuration of

the new device for WPS function meanwhile.

I.

Use the Wi-Fi Protected Setup Button

Use this method if your client device has a Wi-Fi Protected Setup button.

Step 1:

Press the WPS button on the side panel of the Modem Router, as shown in the following

figure.

TD-VG3631

300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide

46

You can also keep the default WPS Status as

Enabled

and click the

Add device

button in Figure

4-26, then Choose “

Press the button of the new device in two minutes

” and click

Connect

.

(Shown in the following figure)

Figure 4-27

Step 2:

Press and hold the WPS button of the client device directly.

Step 3:

The Wi-Fi Protected Setup LED flashes for two minutes during the Wi-Fi Protected Setup

process.

Step 4:

When the WPS LED is on, the client device has successfully connected to the Modem

Router.

Refer back to your client device or its documentation for further instructions.

II.

Enter the client device’s PIN on the Modem Router

Use this method if your client device has a Wi-Fi Protected Setup PIN number.

Step 1:

Keep the default WPS Status as

Enabled

and click the

Add device

button in Figure

4-26, then the following screen will appear.

Figure 4-28