1. Home
    2. /
  2. Manuals
    3. /
  3. TP-Link
    4. /
  4. TD-VG3631
    5. /
  5. 12
Page 56 / 129 Scroll up to view Page 51 - 55
TD-VG3631
300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide
47
Step 2:
Enter the PIN number from the client device in the field on the above WPS screen. Then
click
Connect
button.
Step 3:
“
Connect successfully
” will appear on the screen of Figure 4-28, which means the
client device has successfully connected to the Modem Router.
III. Enter the Modem Router’s PIN on your client device
Use this method if your client device asks for the Modem Router’s PIN number.
Step 1:
On the client device, enter the PIN number listed on the Modem Router’s Wi-Fi
Protected Setup screen. (It is also labeled on the bottom of the Modem Router.)
Step 2:
The Wi-Fi Protected Setup LED flashes for two minutes during the Wi-Fi Protected
Setup process.
Step 3:
When the WPS LED is on, the client device has successfully connected to the Modem
Router.
Step 4:
Refer back to your client device or its documentation for further instructions.
)
Note:
1)
The WPS LED on the Modem Router will light green for five minutes if the device has been
successfully added to the network.
2)
The WPS function cannot be configured if the Wireless Function of the Modem Router is
disabled. Please make sure the Wireless Function is enabled before configuring the WPS.
4.6.3 Wireless Security
Choose menu “
Wireless
”
Æ
”
Wireless Security
”, you can configure the security settings of your
wireless network.
There are three wireless security modes supported by the Modem Router: WEP (Wired Equivalent
Privacy), WPA-PSK (Pre-Shared Key), WPA2-PSK (Pre-Shared Key).
Page 57 / 129
TD-VG3631
300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide
48
Figure 4-29
¾
Disable Wireless Security:
If you do not want to use wireless security, check this radio
button. But it’s strongly recommended to choose one of the following modes to enable
security.
¾
WEP:
It is based on the IEEE 802.11 standard. If you check this radio button, you will find a
notice in red as show in Figure 4-29.
Figure 4-30
•
Auth Type
-
you can choose the type for the WEP security on the drop-down list. The
default setting is
Automatic
, which can select
Shared Key
or
Open System
authentication
type automatically based on the wireless station's capability and request.
•
WEP Key Format
-
Hexadecimal
and
ASCII
formats are provided here
.
Hexadecimal
format stands for any combination of hexadecimal digits (0-9, a-f, A-F) in the specified
length.
ASCII
format stands for any combination of keyboard characters in the specified
length.
Page 58 / 129
TD-VG3631
300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide
49
•
WEP Key
-
Select which of the four keys will be used and enter the matching WEP key that
you create. Make sure these values are identical on all wireless stations in your network.
•
Key Type
-
You can select the WEP key length (64-bit, or 128-bit, or 152-bit.) for encryption.
"Disabled" means this WEP key entry is invalid.
64-bit -
You can enter 10 hexadecimal digits (any combination of 0-9, a-f, A-F, zero key is
not promoted) or 5 ASCII characters.
128-bit -
You can enter 26 hexadecimal digits (any combination of 0-9, a-f, A-F, zero key is
not promoted) or 13 ASCII characters.
152-bit -
You can enter 32 hexadecimal digits (any combination of 0-9, a-f, A-F, zero key is
not promoted) or 16 ASCII characters.
)
Note:
If you do not set the key, the wireless security function is still disabled even if you have selected
Shared Key as Authentication Type.
¾
WPA-PSK /WPA2-PSK:
It’s based on Radius Server.
•
Auth type
-
you can choose the version of the WPA security on the drop-down list. The
default setting is
Auto
, which can select
WPA (
Wi-Fi Protected Access) or
WPA2 (
WPA
version 2) automatically based on the wireless station's capability and request.
•
Encryption -
You can select either
Auto
, or
TKIP
or
AES.
•
PSK Password -
You can enter ASCII characters between 8 and 63 characters or 8 to 64
Hexadecimal characters.
•
Group Key Update Period -
Specify the group key update interval in seconds. The value
should be 30 or above. Enter 0 to disable the update.
Be sure to click the
Save
button to save your settings on this page.
4.6.4 Wireless MAC Filtering
Choose menu “
Wireless
”
Æ
”
MAC Filtering
”, you can control the wireless access by configuring
the
Wireless MAC Filtering
function, shown in Figure 4-31.
Figure 4-31
To filter wireless users by MAC Address, click
Enable
. The default setting is
Disabled
.
¾
MAC Address:
The wireless station's MAC address that you want to filter.
¾
Status:
The status of this entry, either
Enabled
or
Disabled
.
Page 59 / 129
TD-VG3631
300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide
50
¾
Description:
A simple description of the wireless station.
To Add a Wireless MAC Address filtering entry, click the
Add New
button. The following
page will
appear, shown in Figure 4-32:
Figure 4-32
To add or modify a MAC Address Filtering entry, follow these instructions:
1.
Enter the appropriate MAC Address into the
MAC Address
field. The format of the MAC
Address
is
XX:XX:XX:XX:XX:XX
(X
is
any
hexadecimal
digit).
For
example:
00:1D:0F:11:22:33.
2.
Give a simple description for the wireless station in the
Description
field. For example:
Wireless station A.
3.
Select
Enabled
or
Disabled
for this entry on the
Status
drop-down list.
4.
Click the
Save
button to save this entry.
To edit or delete an existing entry:
1.
Click the
Edit
in the entry you want to modify.
2.
Modify the information.
3.
Click the
Save
button.
Click the
Enable/ Disabled Selected
button to make selected entries enabled or disabled.
Click the
Delete Selected
button to selected entries.
For example:
If you desire that the wireless station A with MAC address 00:1D:0F:11:22:33 and the
wireless station B with MAC address 00:0A:EB:00:07:5F are able to access the Modem Router, but
all the other wireless stations cannot access the Modem Router, you can configure the
Wireless
MAC Address Filtering
list by following these steps:
1.
Click the
Enable
button to enable this function.
2.
Select the radio button “
Allow the stations specified by any enabled entries in the list to
access
” for
Filtering Rules
.
3.
Delete all or disable all entries if there are any entries already.
4.
Click the
Add New
button.
1)
Enter the MAC address
00:1D:0F:11:22:33
/
00:0A:EB:00:07:5F
in the
MAC Address
field.
2)
Enter wireless station A/B in the
Description
field.
3)
Select
Enabled
in the
Status
drop-down list.
4)
Click the
Save
button.
Page 60 / 129
TD-VG3631
300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide
51
5)
Click the
Back
button.
The filtering rules that configured should be similar to the following list:
4.6.5 Wireless Advanced
Choose menu “
Wireless
”
Æ
”
Wireless Advanced
”, you can configure the advanced settings of
your wireless network.
Figure 4-33
¾
Transmit Power:
Here you can specify the transmit power of Modem Router. You can select
High, Middle or Low which you would like. High is the default setting and is recommended.
¾
Beacon Interval:
Enter a value between 25-1000 milliseconds for Beacon Interval here. The
beacons are the packets sent by the Modem Router to synchronize a wireless network.
Beacon Interval value determines the time interval of the beacons. The default value is 100.
¾
RTS Threshold:
Here you can specify the RTS (Request to Send) Threshold. If the packet is
larger than the specified RTS Threshold size, the Modem Router will send RTS frames to a
particular receiving station and negotiate the sending of a data frame. The default value is
2346.
¾
Fragmentation Threshold:
This value is the maximum size determining whether packets
will be fragmented. Setting the Fragmentation Threshold too low may result in poor network
performance because of excessive packets. 2346 is the default setting and is recommended.
¾
DTIM Interval:
This value determines the interval of the Delivery Traffic Indication Message
(DTIM). A DTIM field is a countdown field informing clients of the next window for listening to
broadcast and multicast messages. When the Modem Router has buffered broadcast or
multicast messages for associated clients, it sends the next DTIM with a DTIM Interval value.

Rate

3.5 / 5 based on 2 votes.

Popular TP-Link Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top