Page 31 / 120
Scroll up to view Page 26 - 30
LTE/WiMAX DM Outdoor | User Manual
Dual Mode CPE7000 Manual
31
31
LTE Information
State:
Device Init:
Detect LTE module.
SIM Detecting:
As titled.
Device Ready:
Unlock pin code.
Search:
Scan the available eNodeB.
Network Entry:
Cell detection.
Attached:
As titled.
Idle:
As titled.
No Signal:
NAS attached RRC detached.
DL Frequency:
Downlink frequency.
Bandwidth:
As titled.
RSRP1:
Reference signal receiving power of path 1.
CINR0:
The quality of the signal of path 0.
Tx Power:
Transmission power.
Cell ID:
Cell Identity, a part of cell global identification.
UL Frequency:
Uplink frequency.
RSRP0:
Reference Signal Receiving Power Path 0.
RSRQ:
Reference signal receive quality.
CINR1:
The quality of the signal of path 1.
PCI:
Physical cell identity.
Page 32 / 120
LTE/WiMAX DM Outdoor | User Manual
Dual Mode CPE7000 Manual
32
32
WiMAX Information
(Only in WiMAX mode)
WiMAX Information
State
INIT:
Detect WiMAX module.
READY:
Has detected WiMAX module.
SCAN:
Scan available BS.
NETWORK_ENTRY:
Target a base station but not connected.
OPERATOINAL:
Connected to the BS.
Security:
Possible states are unauthorized and authorized. This depends on whether
the authentication is used or not.
Center Frequency:
As titled.
RSSI:
Received signal strength indication.
CINR Reuse1:
A kind of signal quality.
Tx Power:
Transmission power.
BSID:
As titled.
Bandwidth:
As titled.
CINR: as titled.
A kind of signal quality.
CINR Reuse3:
A kind of signal quality.
Max Tx Power:
As titled.
WiMAX TX
(Only in WiMAX mode)
Page 33 / 120
LTE/WiMAX DM Outdoor | User Manual
Dual Mode CPE7000 Manual
33
33
WiMAX TX
Data Rate:
Transmission data rate.
Packets:
Number of transmitted packets.
TX Bytes:
Number of transmitted bytes.
UL MCS:
Uplink Modulation and coding sequence. This includes qpsk-ctc-1/2,
qpsk-ctc-3/4, qam16-ctc-1/2, qam16-ctc-3/4, qam64-ctc-1/2, qam64-ctc-2/3,
qam64-ctc-3/4 and qam64-ctc-5/6.
WiMAX RX
(Only in WiMAX mode)
WiMAX RX
Data Rate:
Receiving data rate.
Packets:
Number of received packets.
MIMO Mode:
Matrix B is for increasing the data rate whereas Matrix A is for increasing
the coverage area or distance.
RX Bytes:
Number of received bytes.
DL MCS:
Downlink modulation and coding sequence. This includes qpsk-ctc-1/2,
qpsk-ctc-3/4, qam16-ctc-1/2, qam16-ctc-3/4, qam64-ctc-1/2, qam64-ctc-2/3,
qam64-ctc-3/4 and qam64-ctc-5/6.
Service Flow
(Only in WiMAX mode)
:
This Field shows detailed information about
“
Service
Flow
”
dispatched by WiMAX base station.
Service Flow
Table
Page 34 / 120
LTE/WiMAX DM Outdoor | User Manual
Dual Mode CPE7000 Manual
34
34
Mobile Network | Technology | Basic
Mobile Network > Technology > Basic
STOP/START Mobile Network:
Click button
“
Start
”
/
”
Stop
”
to start/terminate the WAN
connection.
Mobile Tech Mode Settings:
This option chooses the WAN connection mode of CPE.
If you choose
LTE Only
or
WiMAX Only
, CPE will only seek LTE or WiMAX service.
If you choose
Multi-mode
, Both LTE and WiMAX service would be searched but one at
a time. The user can choose
LTE First
or
WiMAX First
, CPE would interchangeably
search LTE and WiMAX service but search the one you specify first. The searching
process would repeat until CPE is connected to eNodeB or BS.
Cancel button
Reset fields to the last saved values.
Apply button
Commit the changes made and save to the CPE device, some
services will be reloaded.
Page 35 / 120
LTE/WiMAX DM Outdoor | User Manual
Dual Mode CPE7000 Manual
35
35
Mobile Network | Technology | LTE | Cell Selection
Mobile Network > Technology > LTE > Cell Selection
Mode:
TDD only.
Scan Mode:
Full Band or Dedicated Earfcn. Searching full band would take much longer time
than Dedicated Earfcn.
Band:
(40 and / or 41), (42 and / or 43) depend on CPE band.
Type: DL-Earfcn or Dl-Frequency
LTE Band 40, 41 and Earfcn/Frequency Range
are just an example.
Real number is determined by the user's requirement.
Cancel button
Reset fields to the last saved values.
Apply button
Commit the changes made and save to the CPE device, some
services will be reloaded.
19216811.live