Page 31 / 128 Scroll up to view Page 26 - 30
23
3 MANUAL INSTALLATION
DMS-CTC-20101206-0033 v1.0
3.1.1
Setting up your MediaAccess Gateway as DSL
Gateway
Introduction
This section helps you to connect the MediaAccess Gateway to your service provider’s network.
Signal arriving at your home
The
Line
signal that arrives at your home consists the following components:
A
Phone
signal carrying the traffic for telephony.
A
DSL
signal carrying the Internet traffic.
DSL Gateways have a built-in solution to remove the
Phone
component. No additional devices are needed, you can
connect them directly to the
Line
.
Telephones do not have this capability, so here you have to use a filter or splitter to remove the
DSL
signal.
What does a filter/splitter look like
A splitter/filter is a box that typically has the following connectors:
A
Line
input
This connector must be connected to the input signal that needs to be filtered.
A
Phone/PSTN
output
This connector offers filtered output signal. It only contains the
Voice
component and can only be used for connecting
phones.
A
Modem/DSL
output (optional)
This connector offers unfiltered output. It contains both the
Phone
and
DSL
signal and can be used to connect your
MediaAccess Gateway.
Connecting the cables
The procedure to be followed depends on the fact if this filter has been integrated into your MediaAccess Gateway or not.
Check the label of your MediaAccess Gateway. If the product name contains:
“wIF” (for example MediaAccess TG789vn v3
wIF
) then your MediaAccess Gateway has an integrated filter. No external
filters are needed. Follow the steps described in
“Scenario 2: A MediaAccess Gateway without integrated filter” on page 24
.
No “wiF”
(for example MediaAccess TG789vn v3) then your MediaAccess Gateway does
not
have an integrated filter.
Follow the steps described in
“Scenario 2: A MediaAccess Gateway without integrated filter” on page 24
.
This
Phone
signal is only used for communication over the traditional telephone network (PSTN). Voice over IP
communication will be carried by the
DSL
signal.
DSL
+
Voice
Voice
DSL
+
Voice
Service
Provider
Filter/Splitter
LINE
PHONE
MODEM
Page 32 / 128
24
3 MANUAL INSTALLATION
DMS-CTC-20101206-0033 v1.0
Scenario 1: A MediaAccess Gateway with integrated filter
Proceed as follows:
1
Take the DSL cable. This is the gray cable that is included in your box.
2
Plug one end of the cable in the grey
DSL
port on the back of your MediaAccess Gateway.
3
Plug the other end of the cable:
In the
DSL/Modem
output of your
splitter/filter
.
Directly into the telephone wall outlet if there is no
splitter/filter
between the network terminator and your local
phone network.
Scenario 2: A MediaAccess Gateway without integrated filter
Proceed as follows:
1
Take the DSL cable. This is the grey cable that is included in your box.
2
Plug one end of the cable in the grey
DSL
port on the back of your MediaAccess Gateway.
3
Plug the other end of the cable into the
DSL/MODEM
output port of your filter/splitter.
DSL
DSL
Page 33 / 128
25
3 MANUAL INSTALLATION
DMS-CTC-20101206-0033 v1.0
If your MediaAccess Gateway has a black
PSTN
port on the back, you are able to use the PSTN (this is the traditional
telephone network) as a backup for your Voice over IP connection. When the VoIP connection is down, the MediaAccess
Gateway will automatically switch back to the PSTN network.
To setup this backup connection:
1
Take a Telephone Cable
2
Plug one end of the cable in the black
PSTN
port on the back of your MediaAccess Gateway.
3
Plug the other end of the cable into the
Phone
output port of your filter/splitter.
PSTN
Page 34 / 128
26
3 MANUAL INSTALLATION
DMS-CTC-20101206-0033 v1.0
3.1.2
Setting up your MediaAccess Gateway as Local
Router
Procedure
Proceed as follows:
1
Take an Ethernet cable. If your box contains an Ethernet cable with red connectors, you can use that cable.
2
Plug one end of the cable in the
red
WAN port on the back of your MediaAccess Gateway.
3
Plug the other end of the cable into the Ethernet port of your Internet gateway/modem.
The
WAN
port can only be used to connect your MediaAccess Gateway to an Internet gateway/modem. You can
not use it to connect other devices (for example, a computer) to the MediaAccess Gateway.
WAN
Page 35 / 128
27
3 MANUAL INSTALLATION
DMS-CTC-20101206-0033 v1.0
3.2
Powering on the MediaAccess Gateway
Procedure
Proceed as follows:
1
Connect the power cord to the power port of the MediaAccess Gateway.
2
Plug the other end of the power cord into an electrical outlet.
3
Press the power button to turn on the MediaAccess Gateway.
4
Wait at least two minutes to allow the MediaAccess Gateway to complete the start up phase.

Rate

3.5 / 5 based on 2 votes.

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top