Page 21 / 128 Scroll up to view Page 16 - 20
13
1 GETTING STARTED
DMS-CTC-20101206-0033 v1.0
USB LED
Wireless LED
Broadband LED (if you are using the
DSL Gateway
scenario)
Broadband LED (if you are using the
Local Router
scenario)
Internet LED
Colour
State
Description
Green
Solid on
Device(s) connected to the MediaAccess Gateway’s USB port
Off
No device connected to the MediaAccess Gateway’s USB port
Colour
State
Description
Green
Solid on
No wireless activity, WPA2-PSK or WPA-PSK encryption
Blinking
Wireless activity, WPA2-PSK or WPA-PSK encryption
Orange
Solid on
No wireless activity, WEP encryption
Blinking
Wireless activity, WEP encryption
Red
Solid on
No wireless activity, no security
Blinking
Wireless activity, no security
Red/green
Toggling
Wireless client registration phase
Off
Wireless access point disabled
Colour
State
Description
Green
Solid on
DSL line synchronised
Blinking
Trying to detect carrier signal or pending DSL line synchronisation
Off
MediaAccess Gateway powered off.
Colour
State
Description
Green
Solid on
Connected to the WAN device
Off
Not connected to the WAN device
Colour
State
Description
Green
Solid on
Connected to the Internet, no activity
Blinking
Connected to the Internet, sending/receiving data
Red
Solid on
Failed to setup the Internet connection
Off
No Internet connection
Page 22 / 128
14
1 GETTING STARTED
DMS-CTC-20101206-0033 v1.0
TV LED
Phone LED
Upgrade LED
WPS LED
For more information about WPS, see
“5.1 Connecting Your Wireless Client via WPS” on page 44
.
Colour
State
Description
Green
Solid on
Set-Top Box (STB) connected to the MediaAccess Gateway
Blinking
Unknown STB connected to the MediaAccess Gateway
Off
No STB connected to the MediaAccess Gateway
Colour
State
Description
Green
Solid on
Registered at your VoIP provider, no activity.
Blinking
Registered at your VoIP provider, activity.
Off
Not registered to your VoIP provider.
Colour
State
Description
Blue
Solid on
Software upgrade ongoing
Off
No software upgrade ongoing
Do not power off your MediaAccess Gateway or disconnect any cables as long as the
Upgrade
LED is on.
Interrupting the upgrade procedure may damage your MediaAccess Gateway.
Colour
State
Description
Green
Solid On
Client successfully registered via WPS
Orange
Blinking
WPS registration ongoing
Red
Blinking
Error occurred
Page 23 / 128
15
1 GETTING STARTED
DMS-CTC-20101206-0033 v1.0
1.4
Preparing for the Installation
DSL service requirements
This section is only applicable if you are using your MediaAccess Gateway as DSL gateway. For more information, see
“1.2 User Scenarios” on page 5
.
Make sure that:
Your service provider activated the DSL service on your telephone line by your service provider.
You have the installation information (for example, user name, password, service profile,...) provided by your service
provider at hand.
Local connection requirements
Wireless connection
If you want to connect your computer using a wireless connection, your computer must be equipped with a WiFi-certified
wireless client adapter.
Wired connection
If you want to connect a computer using a wired connection, your computer must be equipped with an Ethernet Network
Interface Card (NIC).
Start with the installation
You are now ready to start with the installation of your MediaAccess Gateway.
Page 24 / 128
16
1 GETTING STARTED
DMS-CTC-20101206-0033 v1.0
Page 25 / 128
17
2 GUIDED INSTALLATION
DMS-CTC-20101206-0033 v1.0
2
Guided Installation
Introduction
In the guided installation, the Setup wizard on the Setup CD will assist you with the installation of your MediaAccess
Gateway.
If you do not want to use the Setup CD or if the Setup CD is not included in your package, follow the installation procedure
described in
“3 Manual Installation” on page 21
.
Requirements
To use the guided installation you must comply with the following requirements:
Your computer must run one of the following operating systems:
Microsoft Windows 7 and higher
Microsoft Windows 7 x64 and higher
Microsoft Windows Vista and higher
Microsoft Windows XP Service Pack 2 (SP2) and higher
Mac OS X 10.6 (Snow Leopard)
Mac OS X 10.5 (Leopard)
Mac OS X 10.4 (Tiger)
You must have administrative rights on your computer.
If you do not comply with these requirements, use the
“3 Manual Installation” on page 21
.
Running the Setup wizard
To start the Setup wizard:
1
Insert the Setup CD into your computer's CD- or DVD drive.
2
If your computer runs:
Microsoft Windows: The Setup CD starts automatically.
If the Setup CD does not autostart, see
“The Setup CD does not start automatically” on page 110
.
Mac OS X: Double-click
Menu
in the window with the content of the Setup CD.
3
Select the language of your choice and click
OK
.
4
The Setup wizard will now guide you through the installation of your MediaAccess Gateway.

Rate

3.5 / 5 based on 2 votes.

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top