Page

46

/

84

4.

TOD Filters

Use this page to set rules that will block LAN side PCs from accessing the Internet, but only at specific

days and times. By clicking time block for selecting/deselecting a specific hour. Finally, click the

“

Submit

”

button to save your settings.

Fig.2-28

Parental Control

\TOD Filters



Policies:

A list of available TOD filter policy. Select a policy from the drop list and then click

“

Submit

”

button for making it the current policy. Select a policy from the drop list and then click

“

Remove

”

for removing it. A new policy can be added by clicking

“

Add

”

button. Entering policy

name to

“

Add a Policy

”

dialogue page and clicking

“

Create

”

button for adding it to the list

Page

47

/

84

Fig. 2-29

Parental Control

\Add a Policy



To click on each hour block and making it in blue color will cause the modem to block Internet

traffic at that hour. To click on the blue block again to make it accessable.



Clear:

Click

“

Clear

”

button for clearing all of block hour

.



Inverse:

Click

“

Inverse

”

button for reverse the status of all the hour blocks.

Page

48

/

84

Wireless

–

Wireless Web Page Group

The Wireless web pages group enables a variety of settings that can provide secure and reliable wireless

communications for even the most demanding tech-savvy user.

The Wireless Voice Gateway offers a choice of 802.11b/g/n, WPA and WPA-PSK authentication of your

PCs to the gateway, 64 and 128 bit WEP encryption of communication between the gateway and your

PCs to guaranty security, and an Access Control List function that enables you to restrict wireless access

to only your specific PCs.

Performance

Because your wireless communication travels through the air, the factory default wireless channel setting

may not provide optimum performance in your home if you or your neighbors have other interfering

2.4GHz or 5 GHz devices such as cordless phones. If your wireless PC is experiencing very sluggish or

dramatically slower communication compared with the speed you achieve on your PC that is wired to the

gateway, try changing the channel number. See the 802.11b/g/n Basic Web Page discussion below for

details.

Authentication

Authentication enables you to restrict your gateway from communicating with any remote wireless PCs

that aren’t yours. The following minimum authentication

-related changes to factory defaults are

recommended. See the 802.11b/g/n Basic and Access Control Web Page discussions below for details.

Network Name (SSID)

–

Set a unique name you choose

Network Type

–

Set to Open

Access Control List

–

Enter your wireless PCs’ MAC addresses

Security

Security secures or scrambles messages traveling through the air between your wireless PCs and the

gateway, so they ca

n’t be observed by others. The following minimum security setting changes to factory

defaults are recommended. See the 802.11b/g/n Security Web Page discussion below for details.

Page

49

/

84

1.

2.4 GHz\Radio

This page allows you to configure the access control of 2.4GHz AP

.

Fig.2-30 Wireless\2.4GHz\Radio



Enable:

It may help you to

Enable

or

Disable

the 2.4 GHz wireless function. To enable you need to

select

Enabled

, to disable you need to select

Disabled

.



SSID:

The SSID for 2.4 GHz wireless function.



802.11 Mode:

There are three different modes can be selected. Mixed, Disabled and Greenfield.



Channel:

In 802.11 Band 2.4GHz, there are 1 to 13 channels. In 802.11 Band 5GHz, there are 36,

40, 44, 48 total 4 channels for all country. Choose the one that is suitable for this device.



Bandwidth:

Select wireless channel width

20 MHz

is for default value (bandwidth taken by

wireless signals of this access point.) It can be 20 MHz or 40 MHz.



Power:

This setting decides the output power of this 2.4 GHz device. You may use it to economize

on electricity by selecting lower percentage of power output. Control the range of the AP by

adjusting the radio output power. The power can be 100%, 75%, 50% or 25%.

Page

50

/

84

2.

2.4 GHz\Security

This page allows you to configure security of wireless.

Fig. 2-31

Wireless\2.4GHz\Security



Wireless security mode:

The wireless security mode can be either WPA Personal or WPA.



Authentication:

The method of authentication can be WPA/WPA2 or WPA.



Passphrase:

You can enter ASCII codes into this field. The range is from 8 characters to 64

characters. For

ASCII characters

, you can key in

63

characters in this field. If you want to key in

64

characters, only

hexadecimal characters

can be used.



Retype Passphrase:

Enter the passphrase again for confirmation.