SOHO 18-OB-WR85-FHEU Router Manual PDF (Setup & Configuration Guide)

Page 31 / 69 Scroll up to view Page 26 - 30

30

7.

Use “settime” to change the current system time.

Usage: settime <hh:mm:ss> [yy/mm/dd] [TZ(GMT +/- hour)]

(4)

“ifShow” command shows all network interface information, including IP address, subnet

mask, and information of packets.

Usage: ifShow [ifname]

To show all network interface, just type “ifShow” at command line prompt.

Lo – Loopback interface.

adm – LAN interface.

wlan – Wireless LAN interface.

cmd>ifShow

lo (unit number 0):

Type: SOFTWARE_LOOPBACK

Internet address: 127.0.0.1

Netmask 0xff000000 Subnetmask 0xff000000

Metric is 0

Maximum Transfer Unit size is 1536

0 packets received; 0 packets sent

0 multicast packets received

0 multicast packets sent

0 input errors; 0 output errors

0 collisions; 0 dropped

adm (unit number 0):

Type: ETHERNET_CSMACD

Internet address: 192.168.1.1

Broadcast address: 192.168.1.255

Netmask 0xffffff00 Subnetmask 0xffffff00

cmd>settime 15:50:00 2002/12/13

cmd>time

Time zone:

GMT+6

Local time:

Fri Dec 13 15:50:02 2002

GMT time:

Fri Dec 13 21:50:02 2002

cmd>

Page 32 / 69

31

Ethernet address is 00:01:02:03:04:05

Metric is 0

Maximum Transfer Unit size is 1500

1016 packets received; 686 packets sent

189 multicast packets received

21 multicast packets sent

0 input errors; 0 output errors

0 collisions; 0 dropped

wlan (unit number 0):

Type: ETHERNET_CSMACD

Netmask 0x1114 Subnetmask 0x111c

Ethernet address is 00:02:6f:01:c0:3f

Metric is 0

Maximum Transfer Unit size is 1500

0 packets received; 209 packets sent

0 multicast packets received

0 multicast packets sent

0 input errors; 0 output errors

0 collisions; 0 dropped

cmd>

(5)

“ipConfig” command is used to configure interface address and subnet mask.

Usage: ipConfig [ifname] [ip] [subnetMask]

I

ask]

(6)

“ping” command is used to ping a host.

Usage: ping

[IP address]

Welcome to Telnet Daemon v1.00

cmd>ipConfig adm0 192.168.1.50 255.255.255.0

cmd>

Interface name

IP address

of interface

Subnet Mask

cmd>ping 192.168.1.20

Start time 14671

Reply from 192.168.1.20

End time 14673

Ping statics for 192.168.1.20:

Packets: Sent = 1, Received = 1, Lost = 0

Page 33 / 69

32

(7)

“exit” command exit the telnet session. Type “exit” at command line prompt.

(8)

“wlanShow” command shows the wireless LAN configuration, including SSID, Channel, WEP

Encryption information, threshold information, and security information. Just type “wlanShow”

at command line prompt.

8.“reset” command can reboot the system. Just type ”reset” at command line prompt.

cmd>exit

Exit this telnet session

cmd>wlanShow

------- AP configuration ---------

MAC address 00:02:6f:01:c0:3d

SSID: Candice

Channel: 6

WEP: Disable

Authentication algorithm: Open System

Default Wep key Id(1-4): 1

WEP key len: 64-bit

Key 1: 00000000000000000000000000

Key 2: 00000000000000000000000000

Key 3: 00000000000000000000000000

Key 4: 00000000000000000000000000

--- Wireless Enhanced Features ---

Power Level: MAX(original)

Fragment Threshold: 2346

RTS Threshold: 2432

Beacon Interval 100 (max: 4095 ms default :100ms)

Max associated stations: 250

Wireless Client Isolation: Disable

Hide SSID: Disable

Block Responds to 'Unspecified-SSID': Disable

AP Link Completeness: Disable

Page 34 / 69

33

(9)

“status” shows current information and settings for your AP.

10. “routeShow” shows the network routing table, host routing table and the ARP table.

cmd>status

---==== WAN configuration ====---

WAN mode: 1

WAN mode: DHCP client

IP Address: 192.168.123.157

Subnet Mask: 255.255.255.0

Gateway: 192.168.123.254

MAC address: 00:d0:59:13:3e:92

--------- LAN

-----------------

IP: 192.168.1.133

Subnet Mask: 255.255.255.0

Gateway: 192.72.9.250

LAN MAC Address: 00:02:6f:00:08:41

Connected DHCP Clients: 2

--------- Wireless

-----------------

SSID: [jimmy]

Channel: 6

WEP Security: [Disable]

Wireless MAC address 00:02:6f:01:fa:6b

--------- System Information -----------------

System Up time: 00:14:16

Local time: Thu Jan

1 00:14:16 1970

GMT time: Wed Dec 31 16:14:16 1969

Current Firmware Version: [1.00.4753]

Firmware Date: [2003.02.12]

Hardware Version: [1.0.0]

Serial Number: [00041]

Page 35 / 69

34

cmd>routeShow

Net Routing Table:

Destination

Gateway

NetMask

Flags

Used Hops Interface

192.168.3.0

192.168.3.1

255.255.255.0

U

C

0

adm0

Host Routing Table:

Destination

Gateway

NetMask

Flags

Used Hops Interface

127.0.0.1

U H

0

lo0

ARP Table:

Destination

Gateway

NetMask

Flags

Used Hops Interface

192.168.3.20

00:00:e2:7ª:59:3f

U H

L

3377 0

adm0

192.168.3.25

00:02:6f:01:c0:3d

U H

L

3142 0

adm0

cmd>

11.“dhcpsStart” command enables the DHCP server function. The AP can function as a DHCP

server and automatically assign an IP address to a client.

cmd>dhcpsStart

DhcpsStart: successful!

12. “dhcpsStop” command can stop the DHCP server function.

Welcome to Telnet Daemon v1.01

cmd>dhcpsStop

cmd>

13. “lanShow” command shows the LAN configuration and DHCP configuration, including IP

address, Subnet Mask, DHCP status, and IP pool information.

Rate

Popular SOHO Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share