1. Home
    2. /
  2. Manuals
    3. /
  3. SOHO
    4. /
  4. 18-OB-WR85-FHEU
    5. /
  5. 12
Page 56 / 69 Scroll up to view Page 51 - 55
55
Example:
2.
The “dnssec” action can set the secondary DNS address.
Example:
3.
The “mode” action can change the WAN mode.
1: DHCP client
2: Static IP
3: PPPoE
Example:
4.
The ”static” action can the WAN IP and Subnet Mask for static mode.
Usage: wanSet static [IP address] [netmask] [gateway]
cmd>wanSet dnsprm 192.168.192.74
Old primary DNS IP: 192.72.9.45
New primary DNS IP: 192.168.192.74
(Please remember to reset the Access Point if you made any change).
d>
cmd>wanSet dnssec 192.168.192.55
Old secondary DNS IP: 192.72.9.46
New secondary DNS IP: 192.168.192.55
(Please remember to reset the Access Point if you made any change).
cmd>
Welcome to Telnet Daemon v1.01
cmd>wanSet mode 2
Old WAN mode: DHCP client
New WAN mode: Static IP
(Please remember to reset the Access Point if you made any change).
cmd>wanSet mode
Current WAN mode: Static IP
Page 57 / 69
56
Example:
5.
The “dhcpchost” action can set the DHCP client host name.
Usage: wanSet dhcpchost [hostname]
Example:
6.
The “macaddr” action can set the WAN MAC address.
Usage: wanSet macaddr [mac address]
MAC address format: xx-xx-xx-xx-xx-xx
Example:
6.9
Configuring PPPoE through Telnet
The command “pppoeSet” can change the settings of PPPoE. Type “pppoeSet” and the action you
want to perform. You need to know actions for PPPoE setting.
Usage: pppoeSet [ACTION] [arg1] [arg2]…..
cmd>wanSet static
Usage: WANSet ip [IP address] [netmask] [gateway]
Current WAN IP: 192.72.9.20, mask:255.255.255.0, gateway: 192.72.9.250
cmd>wanSet static 192.72.9.20 255.255.255.0 192.72.9.250
Old WAN IP: 192.72.9.20, mask:255.255.255.0, gateway: 192.72.9.250
New WAN IP: 192.72.9.20, mask:255.255.255.0, gateway: 192.72.9.250
(Please remember to reset the Access Point if you made any change).
cmd>wanSet dhcpchost hello
Old host name:
New host name: hello
(Please remember to reset the Access Point if you made any change).
cmd>wanSet macaddr 00-d0-59-13-3e-92
Old WAN MAC address: 00-d0-59-13-3e-91
New WAN MAC address: 00-d0-59-13-3e-92
(Please remember to reset the Access Point if you made any change).
Page 58 / 69
57
1.
The “name” action can change the PPPoE name.
Usage: pppoeSet name [name]
Example:
2.
The “ password” action can change the PPPoE password.
Usage: pppoeSet password [password]
Example:
ACTION
Description
Usage
name
Change the PPPoE user
name
pppoeSet name [name]
password
Change the PPPoE
password
pppoeSet password
[password]
srvname
Change the Service name
pppoeSet srvname [service
name]
mtu
Change the MTU
pppoeSet mtu [mtu]
Mtu: 1400 – 1492
idletime
Change the maximum idle
time
pppoeSet idletime [idle
time]
Idletime: 0 – 60 min
autoconn
Enable or disable the
auto-reconnect
pppoeSet autoconn [0|1]
0: unselected
1: selected
Welcome to Telnet Daemon v1.01
cmd>pppoeSet name guest
Old User name: s004282
New User name: guest
cmd>
cmd>pppoeSet password guest1
Old Password: test1
New Password: guest1
Page 59 / 69
58
3.
The “srvname” action can change the service name.
Usage: pppoeSet srvname [service name]
Example:
4.
The “mtu” action can change the maximum transmission unit.
Usage: pppoeSet mtu [mtu]
Example:
Note: the default mtu is 1492.
5.
The “ idletime” action can change the maximum idle time.
Usage: pppoeSet idletime [idle time]
Example:
6.
The “autoconn” action can enable or disable the auto-reconnect function.
Usage: pppoeSet autoconn [0|1]
0: Unselected (disable)
1: Selected (enable)
Example:
cmd>pppoeSet srvname http
Old Service name: ftp
New Service name: http
cmd>pppoeSet mtu 1422
Old MTU: 1432
New MTU: 1422
cmd>pppoeSet idletime 30
Old idle time: 40
New idle time: 30
Page 60 / 69
59
Welcome to Telnet Daemon v1.01
cmd>pppoeSet autoconn 1
Old auto reconnection: Unselect
New auto reconnection: Selected
6.10 Upgrading Firmware through Telnet
If problem happens during firmware upgrading (e.g.. Power off abnormally), the AP may not
work normally. If this is the case, the AP will start a Telnet Daemon on the LAN interface. After that,
user can telnet to the AP and make a firmware upgrade using TFTP method. By doing so, user can
make AP works again.
1.
You will see the warning message shown as below:
2.
Connect the managed computer and the AP’s
LAN
port with an Ethernet cable.
3.
Telnet to the AP. Make sure the AP’s IP Address is the one when problem happened.
4.
Type the fixed User Name and Password ( User Name: root / Password: tftp ) to enter the telnet
session.
Verifying product code
......
FAIL
***** WARNING *****
Need to reprogram the Flash. Telnet init
Enter into daemon : Telnet listen Port 23
***** WARNING *****
Need to reprogram the Flash!
User Name :

Rate

4 / 5 based on 2 votes.

Popular SOHO Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top