SOHO 18-OB-WR85-FHEU Router Manual PDF (Setup & Configuration Guide)
Given below is full router user manual of SOHO 18-OB-WR85-FHEU router model. You can also download this manual in PDF Format to read later on your computer.
Product user manuals come handy in case you want to know all functionalities of your device, troubleshooting, fist time configuration & setup and in many other situations.
Page 1 / 69
0
Wireless LAN SOHO Router
User’s Manual
Page 2 / 69
1
CONTENTS
CHAPTER 1 INTRODUCTION
3
1.1 FEATURES
3
1.2 PACKAGE CONTENTS
3
CHAPTER 2 HARDWARE CONFIGURATION
3
2.1 HARDWARE CONFIGURATION
3
2.2 HARDWARE INSTALLATION
3
CHAPTER 3 CONFIGURING YOUR PC
4
CHAPTER 4 INITIAL SOFTWARE INSTALLATION AND CONFIGURATION
5
CHAPTER 5 CONFIGURING THE ROUTER THROUGH WEB BROWSER
6
5.1 SYSTEM SETTINGS
6
5.1.1 System Time
7
5.1.2 Administrator Setting
7
5.1.3 Firmware Upgrade
8
5.1.4 Configuration Tools
10
5.1.5 Status
11
5.1.6 Reset
12
5.2 WAN SETTINGS
12
5.2.1 Dynamic IP Address
13
5.2.2 PPPoE Settings
14
5.2.3 Static IP
15
5.2.4 DNS Settings
15
5.3 LAN SETTINGS
15
5.3.1 LAN Settings
16
5.3.2 DHCP Client Lists
17
5.4 NAT SETTINGS
17
5.4.1 Special Application
17
5.4.2 Virtual Server
18
5.5 FIREWALL SETTINGS
20
5.5.1 Block WAN Ping
20
5.5.2 MAC Control
20
5.5.3 Client Filtering
20
5.6 WIRELESS SETTINGS
21
5.6.1 General
21
5.6.2 Associated Clients
24
5.6.3 Wireless clients MAC Filtering
24
5.7 SNMP
25
Page 3 / 69
2
5.7.1 SNMP Community
25
5.7.2 SNMP Trap
26
CHAPTER 6 CONFIGURING THE ROUTER THROUGH TELNET
27
6.1
ENTER THE TELNET SESSION
27
6.2
COMMAND LINE FOR TELNET DAEMO
N
29
6.3
CONFIGURING WIRELESS
LAN
THROUGH TELNE
T
37
6.4
CONFIGURING
LAN
THROUGH TELNE
T
43
6.5
CONFIGURING SYSTEM THROUGH TELNET
45
6.6
CONFIGURING FIREWALL THROUGH TELNE
T
49
6.7
CONFIGURING
SNMP
THROUGH TELNET
53
6.8
CONFIGURING
WAN
THROUGH TELNE
T
54
6.9
CONFIGURING
PP
P
OE
THROUGH TELNE
T
56
6.10
UPGRADING FIRMWARE THROUGHT TELET
59
APPENDIX A GLOSSARY
APPENDIX B SPECIFICATION
Page 4 / 69
3
Chapter 1
Introduction
1.1 Feature
!
Fully interoperable with IEEE 802.11b compliant products.
!
High-Speed data transfer rate up to 11Mbps.
!
64-bit and 128-bit WEP Encryption.
!
MAC Address and TCP/UDP/IP filtering.
!
Web-Based Network Manager
/
Telnet for Configuring and Managing Your access points.
!
SNMP MIB I and MIB II supported.
!
Capable of acting as a DHCP Server.
!
Remote Management supported.
!
Firmware Upgrade via WEB/TFTP
!
Advanced Firewall features
1.2 Package Contents
!
One CD-ROM with User Guide included
!
One Power Adapter
!
One CAT 5 UTP Cable
!
One Fast Start Guide and One Registration Card
Chapter 2
Hardware Configuration
2.1 Hardware Configuration
1.
RJ-45 Ethernet connector
Provides 10/100 Mbps connectivity to a wired Ethernet LAN.
2.
Reset Button
By pressing this button for over 3 seconds, the AP will be reset with factory default
configuration.
3.
Power Supply connector
It is for connecting to the power adapter.
2.2 Hardware Installation
1.
Configure your notebook or PC with Wireless LAN card.
2.
For Wired LAN, connect your PCs’ Ethernet port to any AP’s LAN port by an Ethernet cable.
3.
For WLAN, locate the AP to a proper position.
4.
Plug the power cord into a power outlet.
Page 5 / 69
4
Chapter 3
Configuring your PC
1.
Change the TCP/IP setting of your managing computer. Select the TCP/IP line that has been
associated to your network card. Click the
Properties
button.
2.
Make sure the IP address of your computer and the AP are in the same subnet. The default IP
address of the access point is 192.168.1.1 and the default subnet mask is 255.255.255.0.
19216811.live