6.69 x 4.33 x 0.98 in (17 x 11 x 2.5 cm) + 1.5 lbs (700g)
Page 97 / 99
T600N - Wireless Dual Band Gigabit Router
97
Problem. I follow the steps, but I am not able to open router’s web management page after type in 192.168.1.1 on my web brows
er.
Solutions.
1. Check if your computer connected to T600N
has being set as a “Fixed IP”. You may want to change to “DHCP” setting
.
•
WIN7 / Vista
1
2
3
4
4
2. Check if your computer is connecting to any wireless / wired network other than
T600N’s.
3. You may have a IP conflict on your modem and the router. Please go to LAN Interface Setup and change the
IP Address
to
192.168.x.1 (x can be any number from 2 to 255), then click
Apply
.
TROUBLESHOOTING
Page 98 / 99
T600N - Wireless Dual Band Gigabit Router
98
Problem. My DSL connection is working, but I can not access the internet with T600N.
•
Solutions.
Your Internet Service Provider (ISP) may require the entering of Login and password. To enter, please
click
PPPoE
under
Internet.
Then enter the connection information provided by your ISP.
Problem. The Setup Wizard does not detect or configure my network.
•
Solutions.
1. Reset your modem, and power off your T600N by unplug the power adapter then plug back in.
2. Allow the wizard to detect your Internet connection one more time. Then follow the Wizard’s instruction
to complete.
3. Or you can check with your ISP for the following connection methods under
Internet
:
•
DSL Connection (Mostly as PPPoE Connection):
Your internet connection needs login information. Please check with ISP if
you do not have on hand.
•
Cable Modem Connection (Mostly as Dynamic IP or Static IP Connection):
Cable modem connection may require you to
clone MAC address.
•
Click
Dynamic IP
under
Internet
, then under
MAC Address
select
Clone MAC
or manually enter the MAC address.
•
Click
Static IP
under
Internet
,
then enter the
IP address
and other connecting information from the ISP.
Problem
. My IP address show up as 169.254.x.x and my computer tells me that I have “Limited or no Connectivity”
•
Solutions.
Check if T600N’s
LAN
under
System
and see if you enable the
DHCP Server
, also check if your computer is set as DHCP setting.
(DHCP should look like below). Restart you computer and try again. If same thing occur, please try using another computer or the wireless
connection.
Problem. I am not getting maximum signal strength when right next to my router.
•
Solutions.
The client may be too close to the router. You may want to step 5 ~ 10 feet away from the router.
You can also change the
wireless channel to avoid wireless interference. Recommended channels use are 1, 6, and 11.
TROUBLESHOOTING
Page 99 / 99
T600N - Wireless Dual Band Gigabit Router
99
FCC STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•
Consult the dealer or an experienced radio/ TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
•
This device may not cause harmful interference.
•
This device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority t
o operate the equipment.
NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMEN
T. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO
OPERATE THE EQUIPMENT.
FCC RF Radiation Exposure Statement
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter.
“To comply with FCC RF exposure compliance requirements, this grant is applicable to only Mobile Configurations. The antennas
used for this transmitter must be installed to provide a separation distance of at least 20 cm
from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter
.”
CE Mark Warning
This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.
National restrictions
This device is intended for home and office use in all EU countries (and other countries following the EU directive 1999/5/EC) without any limitation except for the countries mentioned below:
Country
Restriction
Reason/remark
Bulgaria
None
General authorization required for outdoor use and public service
France
Outdoor use limited to 10 mW e.i.r.p. within the band 2454-
2483.5 MHz
Military Radiolocation use. Refarming of the 2.4 GHz band has been ongoing in recent years to allow current
relaxed regulation. Full implementation planned 2012
Italy
None
If used outside of own premises, general authorization is required
Luxembourg
None
General authorization required for network and service supply(not for spectrum)
Norway
Implemented
This subsection does not apply for the geographical area within a radius of 20 km from the centre of Ny-Ålesund
19216811.live