Page 36 / 127
Scroll up to view Page 31 - 35
300M Wireless N Router
RNX-N300RT
User Manual
Step 4: Wait for a while until the next screen appears. Click
Finish
to complete the WPS
configuration.
The WPS Configuration Screen of Wireless Adapter
4.4.2 By PIN
If the new device supports Wi-Fi Protected Setup and the PIN method, you can add it to
the network by PIN with the following two methods.
Method One:
Enter the PIN into my Router
Step 1: Keep the default WPS Status as
Enabled
and click the
Add device
button in
Figure 4-3, then the following screen will appear.
Figure 4-4
Add A New Device
-35-
Page 37 / 127
300M Wireless N Router
RNX-N300RT
User Manual
Step 2: Choose “
Enter the new device's PIN
” and enter the PIN code of the wireless
adapter in the field after
PIN
as shown in the figure above. Then click
Connect.
)
Note:
The PIN code of the adapter is always displayed on the WPS configuration screen
Step 3: For the configuration of the wireless adapter, please choose “
Enter a PIN into
my access point or a registrar
”
in the
configuration utility of the WPS as below,
and click
Next.
The WPS Configuration Screen of Wireless Adapter
)
Note:
In this example, the default PIN code of this adapter is 16952898 as the above figure
shown.
Method Two:
Enter the PIN from my Router
Step 1: Get the Current PIN code of the Router in Figure 4-3 (each Router has its unique
PIN code. Here takes the PIN code 12345670 of this Router for example).
Step 2: For the configuration of the wireless adapter, please choose “
Enter a PIN from
my access point
”
in the
configuration utility of the WPS as below, and enter the
PIN code of the Router into the field after “
Access Point PIN
”. Then click
Next
.
-36-
Page 38 / 127
300M Wireless N Router
RNX-N300RT
User Manual
The WPS Configuration Screen of Wireless
Adapter
)
Note:
The default PIN code of the Router can be found in its label or the WPS configuration
screen as Figure 4-3.
c)
You will see the following screen when the new device successfully connected to the
network.
)
Note:
1) The WPS LED on the Router will light green for five minutes if the device has been
successfully added to the network.
-37-
Page 39 / 127
300M Wireless N Router
RNX-N300RT
User Manual
2)
The WPS function cannot be configured if the Wireless Function of the Router is
disabled. Please make sure the Wireless Function is enabled before configuring the
WPS.
4.5 Network
Figure 4-5
Network menu
There are three submenus under the Network menu (shown in Figure 4-5):
LAN
,
WAN
and
MAC Clone.
Click any of them, and you will be able to configure the corresponding
function.
4.5.1 LAN
Choose menu “
Network
→
LAN
”, you can configure the IP parameters of the LAN on the
screen as below.
Figure 4-6
LAN
¾
MAC Address
-
The physical address of the Router, as seen from the LAN. The
value can't be changed.
¾
IP Address -
Enter the IP address of your Router or reset it in dotted-decimal
¾
Subnet Mask -
An address code that determines the size of the network. Normally
use 255.255.255.0 as the subnet mask.
-38-
Page 40 / 127
300M Wireless N Router
RNX-N300RT
User Manual
)
Note:
1)
If you change the IP Address of LAN, you must use the new IP Address to log in the
Router.
2)
If the new LAN IP Address you set is not in the same subnet, the IP Address pool of
the DHCP server will change accordingly at the same time
，
while the Virtual Server
and DMZ Host will not take effect until they are re-configured.
4.5.2 WAN
Choose menu “
Network
→
WAN
”, you can configure the IP parameters of the WAN on
the screen below.
1.
If your ISP provides the DHCP service, please choose
Dynamic IP
type,
and the
Router will automatically get IP parameters from your ISP. You can see the page as
follows (Figure 4-7):
Figure 4-7
WAN – Dynamic IP
This page displays the WAN IP parameters assigned dynamically by your ISP,
-39-
19216811.live