Page 106 / 110 Scroll up to view Page 101 - 105
Wireless Router
RNX-EasyN4
User Manual
Once you’ve selected the new firmware file, click <
Apply
> at the bottom of the
screen to start the upgrade process
Page 107 / 110
Wireless Router
RNX-EasyN4
User Manual
- Back-up
The page allows you to save (Backup) the router’s current configuration settings.
When you save the configuration setting (Backup) you can re-load the saved
configuration into the router through the
Restore selection
. If extreme problems
occur you can use the
Restore to Factory Defaults
selection, this will set all
configurations to its original default settings (e.g. when you first purchased the
router).
Backup Settings:
This can save the Broadband router current configuration to a file
named "
config.bin
" on your PC. You can also use the
<Upload>
button to restore the saved configuration to the
Broadband router. Alternatively, you can use the "
Restore to
Factory Defaults
" to force the Broadband router to perform a
power reset and restore the original factory settings.
Page 108 / 110
Wireless Router
RNX-EasyN4
User Manual
- Reset
You can reset the broadband router when system stops responding correctly or
stop functions.
Page 109 / 110
Wireless Router
RNX-EasyN4
User Manual
Appendix A – FCC Interference Statement
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection
against harmful interference in a residential installation.
This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation.
If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one of the following measures:
z
Reorient or relocate the receiving antenna.
z
Increase the separation between the equipment and receiver.
z
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
z
Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment.
IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 20cm between the radiator &
your body.
We declare that the product is limited in CH1~CH11 by specified firmware controlled in the USA.
This transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter.
Page 110 / 110
Wireless Router
RNX-EasyN4
User Manual
Appendix B – IC Interference Statement
Industry Canada statement:
This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
IMPORTANT NOTE:
Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
This device has been designed to operate with an antenna having a maximum gain of 2 dBi. Antenna having
a higher gain is strictly prohibited per regulations of Industry Canada. The required antenna impedance is 50
ohms.
Thank you for purchasing a quality Rosewill Product.
Please register your product at : www.rosewill.com for complete warranty information and future support for your product.

Rate

4.5 / 5 based on 2 votes.

Popular Rosewill Models

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top