1. Home
    2. /
  2. Manuals
    3. /
  3. Peplink
    4. /
  4. Balance_One
    5. /
  5. 11
Page 51 / 234 Scroll up to view Page 46 - 50
USER MANUAL
Peplink Balance Series
-51 / 234 -
Copyright © 2014 Peplink
6.14.3 Rear Panel Appearance
Connector Ports
Power Connector
AC input 100-240V
Switches
Power Switch
Pressing and holding the key for 4 seconds will power down the unit.
When the unit is powered off, pressing this switch will power on the unit.
Power Switch
Power Connector
Page 52 / 234
USER MANUAL
Peplink Balance Series
-52 / 234 -
Copyright © 2014 Peplink
7
Installation
The following section details connecting the Peplink Balance to your network:
7.1
Preparation
Before installing your Peplink Balance, please prepare the following:
At least one Internet/WAN access account
For each network connection, one 10/100BaseT UTP cable with RJ45 connector, or one
1000BaseT Cat5E UTP cable for the Gigabit port on the Balance 580/710/1350/2500, or one
USB modem for the USB WAN port on the Balance 305/380/580/710/1350/2500/MediaFast
A computer with the TCP/IP network protocol and a Web browser installed. Supported browsers
include Microsoft Internet Explorer 8.0 and above, Mozilla Firefox 10.0 and above, Apple Safari
5.1 and above, and Google Chrome 18 and above.
7.2
Constructing the Network
At the high level, construct the network according to the following steps:
1.
With an Ethernet cable, connect a computer to one of the LAN ports on the Peplink Balance. For
the Peplink Balance 20, 30, 30 LTE, 50, 210 and 310, repeat with different cables for up to 4
computers to be connected.
2.
With another Ethernet cable, connect the WAN/broadband modem to one of the WAN ports on
the Peplink Balance. Repeat using different cables to connect from 2 to 13 WAN/broadband
connections (Peplink Balance 20, 30, 30 LTE, 50, 210, 310, 305, 380, 580, 710, 1350, 2500, and
MediaFast) or connect a USB modem to the USB WAN port (Peplink Balance 20, 30, 30 LTE, 50,
380, 580, 710, 1350, 2500, and MediaFast).
3.
For the Peplink Balance 20, 30, 30 LTE, 50, 210, and 310, connect the provided power adapter
to the power connector on the Peplink Balance, and then plug the power adapter into a power
outlet. For the Peplink Balance 305, 380, 580, 710, 1350, 2500, and MediaFast, connect the
provided power cord to the AC power connector on the Peplink Balance, and then plug the power
cord into a power outlet.
The following figure schematically illustrates the resulting configuration:
Page 53 / 234
USER MANUAL
Peplink Balance Series
-53 / 234 -
Copyright © 2014 Peplink
7.3
Configuring the Network Environment
To ensure that your Peplink Balance works properly in the LAN environment and can access the Internet
via the WAN connections, please refer to the following setup procedures:
LAN Configuration
For basic configuration, refer to Section 8,
Basic Configuration
.
For advanced configuration, refer to Section 10,
Configuring the LAN Interfaces(s)
.
WAN Configuration
For basic configuration, refer to Section 8,
Basic Configuration
.
For advanced configuration, refer to Section 12,
Configuring the WAN Interface(s)
.
MediaFast Configuration
For MediaFast configuration, refer to Section 9,
MediaFast Configuration.
Page 54 / 234
USER MANUAL
Peplink Balance Series
-54 / 234 -
Copyright © 2014 Peplink
8
Basic Configuration
8.1
Connecting to the Web Admin Interface
1.
Start a Web browser on a computer that is connected with the Peplink Balance through the LAN.
2.
To connect to the Web Admin of the Peplink Balance, enter the following LAN IP address in the
address field of the web browser:
(This is the default LAN IP address of the Peplink Balance.)
3.
Enter the following to access the Web
Admin Interface.
User Name
: admin
Password
: admin
(This is the default Admin User login of
the Peplink Balance. The Admin and
Read-only User Password can be
changed at
System>Admin Security
.)
4.
After successful login, the
Dashboard
of the Web Admin Interface will be
displayed. It looks similar to the following:
Page 55 / 234
USER MANUAL
Peplink Balance Series
-55 / 234 -
Copyright © 2014 Peplink
Important Note
The
Save
button causes the changes to be saved. Configuration changes (e.g., WAN, LAN, admin settings, etc.)
take effect after clicking the
Apply Changes
button on each page’s top right corner.
8.2
Configuration with the Setup Wizard
The Setup Wizard simplifies the task of configuring WAN connection(s) by guiding the configuration
process step-by-step.
To begin, click
Setup Wizard
after connecting to the Web Admin Interface.
Click
Next
to begin.
Select
YES
if you want to set up Drop-in Mode using the setup wizard (note: Drop-in Mode is available on
the Peplink Balance 210+ and MediaFast 200+).
Click on the appropriate checkbox(es) to select the WAN connection(s) to be configured. If you have
chosen to configure Drop-in Mode using the setup wizard, the box of WAN port that is to be configured in
Drop-in Mode will be checked by default.

Rate

3.5 / 5 based on 2 votes.

Popular Peplink Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top