Page 31 / 234
Scroll up to view Page 26 - 30
USER MANUAL
Peplink Balance Series
-31 / 234 -
Copyright © 2014 Peplink
6.8.3
LCD Display Menu
> HA State: Master/Slave
> LAN IP
> VIP
> System Status
> System
> Firmware ver.
(shows firmware version)
> Serial number
(shows serial number)
> System time
(shows current time)
> System up time
(shows system uptime since last reboot)
> CPU load
(shows current CPU loading, 0-100%)
> LAN
> Status
(shows LAN port physical status)
> IP address
(shows LAN IP address)
> Subnet mask
(shows LAN subnet mask)
> Link status
(shows Connected/Disconnected, IP address list)
> WAN1
> WAN2
> WAN3
> VPN status
(shows Connected/Disconnected)
>
VPN Profile 1
>
VPN Profile 2
>
…
>
VPN Profile n
> Link usage
> Throughput in
(shows transfer rate in Kbps)
> WAN1
> WAN2
> WAN3
> Throughput out
(shows transfer rate in Kbps)
> WAN1
> WAN2
> WAN3
> Data Transfer’d
(shows volume transferred since last reboot in MB)
> WAN1
> WAN2
> WAN3
> Maintenance
> Reboot
> Reboot? (Yes/No)
(to reboot the unit)
> Factory default
> Factory default? (Yes/No)
(to restore factory defaults)
> LAN config
> Port speed
(shows port speed: Auto, 10baseT-FD, 10baseT-HD,
> LAN
100baseTx-FD, 100baseTx-HD, 1000baseTx-FD)
> WAN1
> WAN2
> WAN3
Page 32 / 234
USER MANUAL
Peplink Balance Series
-32 / 234 -
Copyright © 2014 Peplink
6.8.4 Rear Panel Appearance
Connector Ports
Power Connector
AC input 110/220V
Switch
Power Switch
Pressing and holding the key for 4 seconds will power down the unit.
When the unit is powered off, pressing this switch will power on the unit
6.8.5 Unit Label Appearance
Power Connector
Power Switch
Serial Number and
LAN MAC Address
Page 33 / 234
USER MANUAL
Peplink Balance Series
-33 / 234 -
Copyright © 2014 Peplink
6.9
Peplink Balance 380
6.9.1 Front Panel Appearance
6.9.2 LED Indicators
The statuses indicated by the front panel LEDs are as follows:
Power and Status Indicators
Power LED
OFF
–
Power off
GREEN
–
Power on
LAN Port, WAN 1
–
3 Ports
Right LED
ORANGE
–
1000 Mbps
GREEN
–
100 Mbps
OFF
–
10 Mbps
Left LED
Solid
–
Port is connected without traffic
Blinking
–
Data is transferring
OFF
–
Port is not connected
Port Type
Auto MDI/MDI-X ports
Console and USB Ports
Console Port
Reserved for engineering use
USB Ports
For connecting a 4G/3G USB modem
LCD Display
Console
LCD Controls
LAN Port
Power LED
WAN Ports
USB Ports
Page 34 / 234
USER MANUAL
Peplink Balance Series
-34 / 234 -
Copyright © 2014 Peplink
6.9.3
LCD Display Menu
> HA State: Master/Slave
> LAN IP
> VIP
> System Status
> System
> Firmware ver.
(shows firmware version)
> Serial number
(shows serial number)
> System time
(shows current time)
> System up time
(shows system uptime since last reboot)
> CPU load
(shows current CPU loading, 0-100%)
> LAN
> Status
(shows LAN port physical status)
> IP address
(shows LAN IP address)
> Subnet mask
(shows LAN subnet mask)
> Link status
(shows Connected/Disconnected, IP address list)
> WAN1
> WAN2
> WAN3
> VPN status
(shows Connected/Disconnected)
>
VPN Profile 1
>
VPN Profile 2
>
…
>
VPN Profile n
> Link usage
> Throughput in
(shows transfer rate in Kbps)
> WAN1
> WAN2
> WAN3
> Throughput out
(shows transfer rate in Kbps)
> WAN1
> WAN2
> WAN3
> Data Transfer’d
(shows volume transferred since last reboot in MB)
> WAN1
> WAN2
> WAN3
> Maintenance
> Reboot
> Reboot? (Yes/No)
(to reboot the unit)
> Factory default
> Factory default? (Yes/No)
(to restore factory defaults)
> LAN config
> Port speed
(shows port speed: Auto, 10baseT-FD, 10baseT-HD,
> LAN
100baseTx-FD, 100baseTx-HD, 1000baseTx-FD)
> WAN1
> WAN2
> WAN3
Page 35 / 234
USER MANUAL
Peplink Balance Series
-35 / 234 -
Copyright © 2014 Peplink
6.9.4 Rear Panel Appearance
Connector Ports
Power Connector
AC input 110/220V
Switch
Power Switch
Pressing and holding the key for 4 seconds will power down the unit.
When the unit is powered off, pressing this switch will power on the unit.
6.9.5 Unit Label Appearance
Power Connector
Power Switch
Serial Number and
LAN MAC Address
19216811.live