Page 26 / 146
Scroll up to view Page 21 - 25
20
C.
Windows XP:
1.
Click
“Start”
and
“Run”
.
2.
In the open field, enter
“cmd”
then click
“OK”
.
3.
In the command prompt, type
“ipconfig /all”
, then press
“Enter”
All the Ethernet adapter information will be shown in the appear Windows. Check if you can
get the following setting:
±
IP address as
192.168.1.x
±
The Subnet Mask as
255.255.255.0
±
the default gateway as
192.168.1.1
4.
Type
“Exit”
to end up the process.
Page 27 / 146
21
Chapter 4 Device Administration
For your convenience, an Administrative Utility has been programmed into WL-8064ARM Wireless ADSL2/2+
Router. This chapter will explain all the functions in this utility. All the WL-8064ARM Wireless ADSL2/2+
Router based administrative tasks are performed through this web utility.
4.1 Login
To access the WL-8064ARM Wireless ADSL2/2+ Router Configuration screens, follow the following steps will
enable you to log into the WL-8064ARM Wireless ADSL2/2+ Router:
1.
Launch the Web browser (Internet Explorer, Netscape, etc).
2.
Enter the WL-8064ARM Wireless ADSL2/2+ Router default IP address (Default Gateway)
in the address bar then press Enter to Log in.
3.
Entry of the username and password will be prompted. Enter the default login
“Username”
and
“Password”
: The default login Username of the administrator is
“Admin”
, and the default login
Password is
“ovislink”
.
±
Note that the Username and Password are case sensitive.
“Username”
and
“Password”
can be changed after login. Refer to the
Tools
configuration
section for further instruction.
Page 28 / 146
22
Upon entering the address into the web browser, the configurable
HOME
page with all the device
configuration information will pop up as shown in Figure below.
±
HOME:
The
Home
section show the current WL-8064ARM Wireless ADSL2/2+ Router’s function
information under different links.
±
EZ SETUP:
The
EZ Setup
is meant to help you install the WL-8064ARM Wireless ADSL2/2+
Router quickly and easily.
±
CONFIG:
The
Config
section allows you to create new connections, edit existing connections,
and configure other basic settings.
±
ADVANCED:
The
Advanced
section lets you configure advanced features like RIP, Firewall, NAT,
UPnP, IGMP, Bridge Filters, and LAN clients.
±
WIRELESS:
The
Wireless
section lets you configure wireless connection and related features.
±
TOOLS:
The
Tools
section lets you carry out system commands and perform simple system tests.
±
STATUS:
The
Status
section displays status, log and statistical information for all connections and
interfaces.
±
HELP:
The
Help
section provides information on configuration and settings for each section.
Page 29 / 146
23
±
Status Information:
Shows the current device connection status.
;
System Uptime:
This field displays the time of the WL-8064ARM Wireless ADSL2/2+
Router has been in operation.
;
DSL Status:
Shows the WL-8064ARM Wireless ADSL2/2+ Router connection status.
;
DSL Speed:
This field displays the WL-8064ARM Wireless ADSL2/2+ Router
Downstream/Upstream data rate in Kbps
;
Wireless RF:
Show the WL-8064ARM Wireless ADSL2/2+ Router wireless system status.
;
Ethernet:
This field displays the link up or down for the Ethernet connection.
;
USB:
This field displays the link up or down for the USB connection (Optional).
;
Software Version:
This field displays the WL-8064ARM Wireless ADSL2/2+ Router’s code
version.
;
Firmware Version:
This field displays the WL-8064ARM Wireless ADSL2/2+ Router’s
firmware version.
;
SSID:
The Service Set Identifier (
SSID
) is a unique name for your wireless network. If you
have other wireless access points in your network, they must share the same SSID. The
default SSID is
TI-AR7WRD
.
±
Log Out:
Click to
Log Out the Administration configuration page.
±
Refresh:
Click to Refresh current page.
Page 30 / 146
24
4.2 EZ SETUP
The
EZ SETUP
is meant to help you install the WL-8064ARM Wireless ADSL2/2+ Router quickly and easily.
Click on
“Wizard”
and the following screen will pop-up. Follow the
Steps
describe below to complete your
installation.
19216811.live