Page 16 / 146
Scroll up to view Page 11 - 15
10
Chapter 2 Knowing WL-8064ARM Wireless ADSL2/2+ Router
2.1 Front Panel:
The WL-8064ARM Wireless ADSL2/2+ Router’s LEDs indicators display information about the device’s
status.
Page 17 / 146
11
2.2 Back Panel:
The back panel of the WL-8064ARM Wireless ADSL2/2+ Router contains ADSL, Ethernet Switches, Reset,
Power Adapter connection and SMA connector.
Resetting Factory Defaults:
The reboot and restore to factory defaults feature will set the device to its factory default configuration by
resetting the WL-8064ARM Wireless ADSL2/2+ Router.
To Reset the WL-8064ARM Wireless ADSL2/2+ Router:
±
Ensure that the device is powered on.
±
Press the Reset button for 10~15 seconds and release. The
“WL ACT”
LED indicators will turns OFF
and ON again indicates that the reset is in progress. Do not power off the device during the reset process.
±
Reset is completed when the
“WL ACT”
LED indicator return to steady green. The default settings are
now restored.
All the Ethernet port of the WL-8064ARM Wireless ADSL2/2+ Router
supports auto-crossover capability.
!
RESET Button
:
Reboot & Restore the WL-8064ARM Wireless ADSL2/2+ Router to factory
defaults.
!
Page 18 / 146
12
2.3 Connection Mechanism:
This section describes the hardware connection mechanism of WL-8064ARM Wireless ADSL2/2+ Router on
your Local Area Network (LAN) connected to the Internet, how to configure your WL-8064ARM Wireless
ADSL2/2+ Router for Internet access or how to manually configure your Internet connection.
You need to prepare the following items before you can establish an Internet connection through your
WL-8064ARM Wireless ADSL2/2+ Router:
1.
A computer/notebook which must have an installed Ethernet Adaptor and an Ethernet Cable, or
2.
A computer/notebook which have Wireless-b or Wireless-g wireless adaptor properly installed.
3.
ADSL/ADSL2/ADSL2+ service account and configuration information provided by your Internet Service
Provider (ISP). You will need one or more of the following configuration parameters to connect your
WL-8064ARM Wireless ADSL2/2+ Router to the Internet:
a.
VPI/VCI parameters
b.
Multiplexing Method or Protocol Type
c.
Host and Domain Names
d.
ISP Login Name and Password
e.
ISP Domain Name Server (DNS) Address
f.
Fixed or Static IP Address.
Figure below shows the overall hardware connection mechanism of your WL-8064ARM Wireless ADSL2/2+
Router
.
Page 19 / 146
13
Following are the steps to properly connect your WL-8064ARM Wireless ADSL2/2+ Router:
1.
Turn off your computer/notebook.
2. Connect the ADSL port of your WL-8064ARM Wireless ADSL2/2+ Router to the wall jack of the
ADSL/ADSL2/ADSL2+ Line with a RJ-11 cable.
3.
Connect the Ethernet cable (RJ-45) from your WL-8064ARM Wireless ADSL2/2+ Router (Switch ) to the
Ethernet Adaptor in your computer.
4.
Connect the Power adaptor to the WL-8064ARM Wireless ADSL2/2+ Router and plug it into a Power
outlet.
5.
Turn on your computer.
6.
Refer to the next section to setup or configure your system’s Network Adaptor.
The Power light will lit after turning on the WL-8064ARM Wireless
ADSL2/2+ Router.
Auto and self-diagnostic process might turn the LED indicators ON and
OFF during the process.
!
Page 20 / 146
14
Chapter 3 Setting up the TCP/IP in Windows
The instruction in this chapter will help you configure your computers to be able to communicate with this
WL-8064ARM Wireless ADSL2/2+ Router.
Computers access the Internet using a protocol called TCP/IP (Transmission Control Protocol/ Internet
Protocol). Each computer/notebook on your network must have TCP/IP installed and selected as its
networking protocol. If a Network Interface Card (NIC) is already installed in your PC, then TCP/IP is probably
already installed as well.
The following description assumes WL-8064ARM Wireless ADSL2/2+ Router been set to factory default. (If
not, please hold the reset button down for 5~10 seconds). The default of the WL-8064ARM Wireless
ADSL2/2+ Router’s LAN IP is
192.168.1.1
.
Follow the procedures below to set your computer/notebook function as a
DHCP Client
.
!
Restart and Reboot your Windows system might be necessary after setting your
computer function as a DHCP Client. In order to properly activate your choice, click
“OK” to restart your Windows system.
19216811.live