WF-2409

User Manual

**-**-**-**-**-**

（

e.g.: 00-22-33-da-cc-bb

）

.

Follow the following steps to set Wireless Access Control:

1. Enable Wireless MAC Address Filter, then select save.

2. Add MAC address you want to control in the “MAC address” field (the format is

**-**-**-**-**-**), then click “Add” button, and you will see the MAC address has displayed

in the MAC list.

3. There are two items supplied, “Permit wireless connection for MAC address listed (others

are Denied)” and “Deny wireless connection for MAC address listed (others are Permitted)”,

Select the item you want, and click “Save” button.

4.5.4.

WDS Settings

If you have selected WDS or AP+WDS mode in Wireless Basic-Radio Mode, please do the

following configurations.

Figure 4-37

¾

WDS Name: Give a description of your wireless bridge to tell apart.

¾

WDS MAC Address: If the current working mode is “WDS” or “AP+WDS”, then you

need to configure wireless bridge configuration. Enter MAC address of remote access

point, at the same time the remote access point also need to configure to “WDS”

or ”AP+WDS” mode.

¾

Encryption Type: select AES or TKIP as the Encryption Type

¾

Key Mode: choose the format of password; it should be HEX or ASCII. The valid

character for HEX format should be numbers from 0 to 9 and letters from A to F. HEX

support mixed letter and number mode. And ASCII supports all characters that in

50

WF-2409

User Manual

keyboard.

Figure 4-38

AP1:

¾

Select radio mode is WDS or AP+WDS

in wireless base of AP1.

¾

Click on ‘Wireless’- ‘Wireless Security’ and select and save None as authentication type.

¾

Click on ‘Wireless’- ‘WDS Settings’ ,Input WDS name (e.g.: default), input MAC address

of AP2 (00-22-4f-bc-af-5d), click add, then the record named default will appears in WDS

list.

¾

Click on ‘Wireless’- ‘WDS Settings’ and select the same WDS authentication type and

password with AP2’s Settings and save.

¾

Select Channel is ‘Channel 6’in wireless base of AP2.

AP2:

¾

Select radio mode is WDS or AP+WDS

in wireless management-basic of AP2.

¾

The IP address of AP2 should be 192.168.1.x (1<x<255,e.g.: x=8).

¾

Select ‘Network’-‘DHCP ’ ,select disable DHCP server.

¾

Click on ‘Wireless’- ‘WDS Settings’, Input WDS name (e.g.: Default), input MAC

address of AP1 (00-22-4f-cc-ae-f5), click add, then the record named Default will

appears in WDS list.

¾

Select Channel is ‘Channel 6’in wireless base of AP2.

Note: Before you setup WDS connection, please make sure that AP1 and AP2 is in the same

network, that is if the IP address of AP1 is 192.168.1.1, then the IP address of AP2 should be

192.168.1.x (1<x<255,e.g.: x=8).

51

WF-2409

User Manual

4.5.5.

Repeater Settings

Wireless Repeater mode, is used to relay the wireless signal from a relay point to the next

point, relay and amplify the signals and form a new wireless coverage area.

Figure 4-39

AP1:

¾

Select radio mode is ‘Access Point’ in wireless base of AP1.

¾

Select Channel is ‘Channel 6’ in wireless base of AP1.

52

WF-2409

User Manual

Figure 4-40

AP2:

¾

Select radio mode is ‘REPEATER’ in wireless base of AP2.

¾

Click ‘AP Scan’ in wireless base of AP2 ,and select ‘Netis1’ and Connect , then the

‘Repeater SSID’ and ‘

Channel

’ become same as AP1.

¾

The IP address of AP2 should be 192.168.1.x (1<x<255,e.g.: x=8).

¾

Select ‘Network’-‘DHCP ’ ,select disable DHCP server.

53

WF-2409

User Manual

Figure 4-41

AP3:

¾

Select radio mode is ‘REPEATER’in wireless base of AP3.

¾

Click ‘AP Scan’ in wireless base of AP3 ,and select ‘Netis1’ and Connect , then the

‘Repeater SSID’ and ‘Channel’ become same as AP2.

¾

The IP address of AP3 should be 192.168.1.x (1<x<255),but different from AP2.

¾

Select ‘Network’-‘DHCP ’ ,select disable DHCP server.

4.5.6.

Wireless Advanced

These settings are only for more technically advanced users who have a sufficient knowledge

about wireless LAN. These settings should not be changed unless you know what effect the

change will have on your AP.

54