Page 66 / 74
Scroll up to view Page 61 - 65
WF-2409
User Manual
field, such as www.163.com.
Follow these steps to set Domain filter:
1. You can select “enable” and click “Save” to enable “Domain Filter” function. This is only the
first step, you should continued to create appropriate rules for “Domain Filter”.
2. Input DNS Filter Key words.
3. There are two items supplied, “Permit through the router for DNS Key words listed, others
are denied” and “Deny through the router for DNS Key words listed, others are permitted”,
Select the item you want, and click “Save” button.
4. If you want to delete certain item on the list, select appropriate item on the list, click “delete”
to delete it.
4.9.
Advance
4.9.1.
Static Routing
Most of router and wireless router are using NAT mode, so this feature is designed for most
common network environment.
Figure 4-55
¾
IP Address: Specify a certain IP address which static route forward to.
¾
Subnet Mask: Subnet mask is used for distinguish Network portion and Host portion for an
IP address.
¾
Next-hop IP Address: This is an IP address of the next-hop device (and also is the gateway
65
Page 67 / 74
WF-2409
User Manual
address for local host) that allows forwarding data between router and remote network or
host.
Routing Table: You can check out all current route items, click “delete” button to delete an
route item existed in routing table.
4.9.2.
Dynamic DNS
The DDNS feature allows you using domain name (not IP address) to access Internet. Before
you can use this feature, you need to register an account for DDNS service at DDNS service
providers, such as “roay.cn”, ”TZO.com”, ”DynDNS”. For more information, you can
Figure 4-56
¾
DDNS Status: Current status of DDNS server.
¾
DDNS Server Provider: For example, if you want to use service of “roay.cn”, you have to
first register and accounts for it. Other DDNS service providers as the same.
¾
Username, Password: After register an DDNS account from DDNS service providers, you
will get “User Name”, “Password”, Input information in appropriate field.
4.9.3.
Time Settings
You can choose the time server and the time zone for the system time
66
Page 68 / 74
WF-2409
User Manual
Figure 4-57
4.9.4.
Port Triggering
Port trigger module dynamically registers virtual server rules when any IP host generates the
packet from the specified trigger protocol and port. Port trigger module use forward protocol
type and port number and use the IP address of host that generates the trigger packet when it
registers a rule.
Figure 4-58
¾
Predefined Trigger Rules: select one of the Predefined Rules.
¾
Name: describe one Predefined Trigger that you will configure.
¾
Trigger Protocol: you can select TCP/UDP.
67
Page 69 / 74
WF-2409
User Manual
¾
Trigger Port: you can select a part of ports.
¾
Forward Protocol: you can select TCP/UDP.
¾
Forward Port: you can select a part of ports.
4.9.5.
VPN Settings
VPN is commonly used for encapsulate and encrypt data across the public network. For VPN
tunnel, the router supports IPSEC pass-through, PPTP pass-through and L2TP pass-through.
Figure 4-59
4.9.6.
IGMP Proxy
Here you can set the IGMP Proxy ‘Enabled’ and ‘Disabled’.
Figure 4-60
4.10.
System Tools
System management includes password setup, Firmware, reboot, Remote Management ,
Factory Defaults, and Parameters backup
68
Page 70 / 74
WF-2409
User Manual
4.10.1.
Firmware
Click "Browse..."button and select a File to upgrade, after you have selected the appropriate file,
click "Upgrade" button to execute upgrade procedure. Do not cut off the power supply during
the process of upgrading.
Figure 4-61
4.10.2.
Password
The default username/password is guest/guest. To ensure the Router’s security, it is suggested
that you change the default password to one of your choice, here enter a new password and then
Re-enter it again to confirm your new password. Click “Save” button to save settings.
Figure 4-62
4.10.3.
Parameters Backup
Here you can Backup and Recovery system Configuration Parameter
69
19216811.live