Page 11 / 62
Scroll up to view Page 6 - 10
www.netcomm.com.au
11
NetComm NP805N
–
Gigabit Wireless Router
YMLO-805N
Hardware installation
1.
Connect the power adapter to the Power socket on the back of the NP805N. Plug the power adapter into the wall socket
and switch on the power.
2.
Wait approximately 60 seconds for the NP805N to power up.
Connecting via a cable
1.
Connect the yellow Ethernet cable provided to one of the ports marked
‘
LAN
’
at the back of the NP805N.
2.
Connect the other end of the yellow Ethernet cable to your computer.
3.
Wait approximately 30 seconds for the connection to establish.
4.
5.
Follow the steps to set up your NP805N.
Connecting wirelessly
1.
Ensure Wi-Fi is enabled on your device (computer/laptop/Smartphone).
2.
Scan for wireless networks in your area and connect to the network name that matches the Wireless network name
configured on the NP805N.
Please note: Refer to the included Wireless Security Card for the default SSID of your NP805N
3.
When prompted for your wireless security settings, enter the Wireless security key configured on the NP805N.
Please note: Refer to the included Wireless Security Card for the default wireless security key of your NP805N
4.
Wait approximately 30 seconds for the connection to establish.
5.
6.
Follow the steps to set up your NP805N.
Page 12 / 62
NP805N
–
Gigabit Wireless Router
12
NetComm NP805N - Gigabit Wireless Router
YMLO-805N
www.netcomm.com.au
Web Based Configuration
Interface
First-time Setup Wizard
Please follow the steps below to configure your NP805N Wireless router via the web based configuration wizard.
Open your web browser (e.g. Internet Explorer/Firefox/Safari) and type
into the address bar at the top of the
window.
At the login screen, type "admin" (without quotes) in the username and password field. Then click on Login.
Please note: admin is the default username and password for the unit.
1.
Click on “Yes, let’s get started with the wizard”.
This page enables you to enter the information needed to setup your Internet connection.
2.
From the WAN type pull down menu, select the type of Internet connection you would like to utilise. You can select from:
o
Dynamic IP Address
o
Static IP Address
o
PPP over Ethernet
o
PPTP
o
L2TP
Page 13 / 62
www.netcomm.com.au
13
NetComm NP805N
–
Gigabit Wireless Router
YMLO-805N
Dynamic IP Address
1.
Enter the Host Name (if required).
2.
Enter the ISP registered MAC Address (if required).
3.
Click “Next”.
Static IP Address
1.
Enter the Static IP Address for your connection.
2.
Enter the Subnet Mask for your connection.
3.
Enter the Static Gateway for your connection.
4.
Enter the Static Primary DNS for your connection.
5.
Enter the Static Secondary DNS for your connection (if available).
6.
Click “Next”.
Page 14 / 62
NP805N
–
Gigabit Wireless Router
14
NetComm NP805N - Gigabit Wireless Router
YMLO-805N
www.netcomm.com.au
PPP over Ethernet
1.
Enter the Username required for your PPPoE connection.
2.
Enter the Password required for your PPPoE connection.
3.
Click “Next”.
PPTP
1.
Select to use either a static or dynamically assigned IP address for your connection. When selecting to utilise a static IP
address, you will also need to enter the PPTP IP Address, PPTP Subnet Mask and PPTP Default gateway in use for the
connection
(Refer to your PPTP administrator for more information)
.
2.
Enter the Username required for your PPTP connection.
3.
Enter the Password required for your PPTP connection.
4.
Click “Next”.
Page 15 / 62
www.netcomm.com.au
15
NetComm NP805N
–
Gigabit Wireless Router
YMLO-805N
L2TP
1.
Select to use either a static or dynamically assigned IP address for your connection. When selecting to utilise a static IP
address, you will also need to enter the L2TP IP Address, L2TP Subnet Mask and L2TP Default gateway in use for the
connection
(Refer to your L2TP administrator for more information)
.
2.
Enter the Username required for your L2TP connection.
3.
Enter the Password required for your L2TP connection.
4.
Click “Next”.
19216811.live