Page 41 / 116
Scroll up to view Page 36 - 40
TELSTRA TURBO 7 WIRELESS GATEWAY (3G10WVT) - USER GUIDE
41
6.1.4
Update Firmware
The following screen appears when selecting Update Firmware.By following the steps on this
screen,you can update your Gateway’s firmware.Manual device upgrades from a locally stored
file can also be performed using the following screen.
1:
Obtain an updated software image file
2:
Enter the path and filename of the firmware image file in the Software File Name field or
click the Browse button to locate the image file.
3:
Click the Update Software button once to upload and install the file.
NOTE:
The update process will take about 2 minutes to complete.The Gateway will reboot and the browser window will
refresh to the default screen upon successful installation.
It is recommended that you compare the Software Version at the top of the Basic screen (WUI homepage) with the
firmware version installed,to confirm the installation was successful.
Page 42 / 116
TELSTRA TURBO 7 WIRELESS GATEWAY (3G10WVT) - USER GUIDE
42
6.2
ACCESS CONTROL
The Access Control option found in the Management drop down menu configures access related
parameters in the following three areas:
•
Services
•
IP Addresses
•
Passwords
Access Control is used to control local and remote management settings for your Gateway.
6.2.1
Services
The Service Control List (SCL) allows you to enable or disable your Local Area Network (LAN) or
Wide Area Network (WAN) services by ticking the checkbox as illustrated below.These access
services are available:FTP,HTTP,ICMP,SSH,TELNET,and TFTP.Click Save/Apply to continue.
Page 43 / 116
TELSTRA TURBO 7 WIRELESS GATEWAY (3G10WVT) - USER GUIDE
43
6.2.2
IP Address
The IP Address option limits local access by IP address.When the Access Control Mode is enabled,
only the IP addresses listed here can access the device.Before enabling Access Control Mode,add
IP addresses with the Add button.
On this screen, enter the IP address Subnet Mask and the different interface for which you wish to allow
permission.Click Save/Apply to continue.
Page 44 / 116
TELSTRA TURBO 7 WIRELESS GATEWAY (3G10WVT) - USER GUIDE
44
6.2.3
Passwords
The Passwords option configures your account access password for your Gateway.Access to the
device is limited to the following three user accounts:
•
admin is to be used for local unrestricted access control
•
support is to be used for remote maintenance of the device
•
user is to be used to view information and update device firmware
Use the fields illustrated in the screen below to change or create your password.Passwords must
be 16 characters or less with no spaces.Click Save/Apply to continue.
Page 45 / 116
TELSTRA TURBO 7 WIRELESS GATEWAY (3G10WVT) - USER GUIDE
45
6.3 CONFIGURE SNMP AGENT ON THE 3G10WVT
The Simple Network Management Protocol (SNMP) allows a network administrator to monitor
a network by retrieving settings on remote network devices.To do this,the administrator
typically runs an SNMP management station program such as MIB browser on a local host to
obtain information from the SNMP agent,in this case the 3G10WVT (if SNMP enabled).An SNMP
‘community’performs the function of authenticating SNMP traffic.A‘community name’acts as a
password that is typically shared among SNMP agents and managers.
By default,SNMP agent is enabled on the gateway.
SETTING UP SNMP AGENT
1.
Open a web browser (IE/Firefox/Safari),type in LAN address of the gateway (
http://10.0.0.138by default) to log into the web interface.
2.
The login username and password by default is admin/admin.
3.
Go to Advanced Settings > SNMP.Enable SNMP agent and set up all options according to the
screenshot below.
4.
Click Save/Apply to activate these settings.
19216811.live