Motorola Netopia-3000 Router Manual PDF (Setup & Configuration Guide)

Page 286 / 351 Scroll up to view Page 281 - 285

286

out, each heartbeat sequence will send out a total 20 heartbeats, spaced at 30 second

intervals, and then sleep for 30 minutes. So to have the Gateway send out packets

“forever”, this number can be set very high. If it is 1440 and the interval is 1 minute,

say, the heartbeat will go out every minute for 1440 minutes, or one day, before sleep-

ing.

•

The

sleep

setting is part of sequence control. This is the time to sleep before starting

another heartbeat sequence, in d:h:m:s.

Page 287 / 351

287

CONFIG Commands

set system ntp

option [ off | on ]:

server-address (204.152.184.72)

alt-server-address (18.72.0.3):

time-zone [ -12 - 12 ]

update-period (60) [ 1 - 65535 ]:

daylight-savings [ off | on ]

Speciﬁes the NTP server address, time zone, and how often the Gateway should check the

time from the NTP server. NTP time-zone of 0 is GMT time; options are -12 through 12 (+/-

1 hour increments from GMT time).

update-period

speciﬁes how often, in minutes, the

Gateway should update the clock.

daylight-savings

speciﬁes whether daylight savings

time is in effect; it defaults to

off

.

set system zerotouch option [ on | off ]

Enables or disables the Zero Touch option.

Zero Touch refers to automatic conﬁguration of your Netopia Gateway. The Netopia Gate-

way has default settings such that initial connection to the Internet will succeed. If the

zerotouch

option is set to

on

, HTTP requests to any destination IP address except the IP

address(es) of the conﬁgured redirection URL(s) will access a redirection server. DNS traf-

ﬁc will not be blocked. Other trafﬁc from the LAN to all destinations will be dropped.

set system zerotouch redirect-url

redirection-URL

Speciﬁes the URL(s) of the desired redirection server(s) when the

zerotouch

option is set

to

on

. URLs may be a maximum of 192 characters long, and may be in any of the following

forms:

http://<domain-name OR IP address>/optionalPath:port

http://<domain-name OR IP address>/optionalPath

https://<domain-name OR IP address>/optionalPath:port

https://<domain-name OR IP address>/optionalPath

<domain-name OR IP address>/optionalPath:port

<domain-name OR IP address>/optionalPath

If the port number is omitted, port 80 will be assumed. Save and Restart are required to

enforce these commands.

Page 288 / 351

288

Syslog

set system syslog option [ off | on ]

Enables or disables system syslog feature. If syslog option is

on

, the following commands

are available:

set system syslog host-nameip [

ip_address

|

hostname

]

Speciﬁes the syslog server’s address either in dotted decimal format or as a DNS name up

to 64 characters.

set system syslog log-facility [ local0 ... local7 ]

Sets the UNIX syslog Facility. Acceptable values are

local0

through

local7

.

set system syslog log-violations [ off | on ]

Speciﬁes whether violations are logged or ignored.

set system syslog log-accepted [ off | on ]

Speciﬁes whether acceptances are logged or ignored.

set system syslog log-attempts [ off | on ]

Speciﬁes whether connection attempts are logged or ignored.

Default

syslog

installation procedure

1.

Access the router via telnet from the private LAN.

DHCP server is enabled on the LAN by default.

2.

The product’s stateful inspection feature must be enabled in order to

examine TCP, UDP and ICMP packets destined for the router or the private

hosts.

This can be done by entering the

CONFIG

interface.

• Type

config

• Type the command to enable stateful inspection

Page 289 / 351

289

CONFIG Commands

set security state-insp eth B option on

• Type the command to enable the router to drop fragmented packets

set security state-insp eth B deny-fragments on

3.

Enabling syslog:

• Type

config

• Type the command to enable syslog

set system syslog option on

• Set the IP Address of the syslog host

set system syslog host-nameip <ip-addr>

(example:

set system syslog host-nameip 10.3.1.1

)

• Enable/change the options you require

set system syslog log-facility local1

set system syslog log-violations on

set system syslog log-accepted on

set system syslog log-attempts on

4.

Set NTP parameters

• Type

config

• Set the time-zone – Default is 0 or GMT

set system ntp time-zone <zone>

(example:

set system ntp time-zone –8

)

• Set NTP server-address if necessary (default is 204.152.184.72)

set system ntp server-address <ip-addr>

(example:

set system ntp server-address 204.152.184.73

)

• Set alternate server address

set system ntp alt-server-address <ip-addr>

5.

Type the command to save the conﬁguration

• Type

save

• Exit the conﬁguration interface by typing

exit

• Restart the router by typing

restart

The router will reboot with the new conﬁguration in effect.

Page 290 / 351

290

Wireless Settings (supported models)

set wireless option ( on | off )

Administratively enables or disables the wireless interface.

set wireless network-id ssid {

network_name

}

Speciﬁes the wireless network id for the Gateway. A unique

ssid

is generated for each

Gateway. You must set your wireless clients to connect to this exact id, which can be

changed to any 32-character string.

set wireless auto-channel mode { off | at-startup | continuous }

Speciﬁes the wireless AutoChannel Setting for 802.11G models. AutoChannel is a feature

that allows the Netopia Gateway to determine the best channel to broadcast automatically.

For details, see

“

Advanced

” on page

57

.

set wireless default-channel { 1...14 }

Speciﬁes the wireless 2.4GHz sub channel on which the wireless Gateway will operate. For

US operation, this is limited to channels 1–11. Other countries vary; for example, Japan is

channel 14 only. The default channel in the US is 6. Channel selection can have a signiﬁ-

cant impact on performance, depending on other wireless activity in proximity to this AP.

Channel selection is not necessary at the clients; clients will scan the available channels

and look for APs using the same ssid as the client.

set wireless network-id closed-system { on | off }

When this setting is enabled, a client must know the ssid in order to connect or even see

the wireless access point. When disabled, a client may scan for available wireless access

points and will see this one. Enable this setting for greater security. The default is

on

.

Rate

Popular Motorola Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share