Motorola 3347 Qwest Router Manual PDF (Setup & Configuration Guide)

Page 171 / 351 Scroll up to view Page 166 - 170

171

SHELL Commands

Common Commands

arp

nnn.nnn.nnn.nnn

Sends an Address Resolution Protocol (ARP) request to match the

nnn.nnn.nnn.nnn

IP

address to an Ethernet hardware address.

clear [yes]

Clears the conﬁguration settings in a Motorola Netopia® Gateway. If you do not use the

optional

yes

qualiﬁer, you are prompted to conﬁrm the

clear

command.

clear_certiﬁcate

Removes an SSL certiﬁcate that has been installed.

clear_log

Erases the log information stored in ﬂash if persistent logging is enabled.

conﬁgure

Puts the command line interface into Conﬁgure mode, which lets you conﬁgure your Motor-

ola Netopia® Gateway with Conﬁg commands. Conﬁg commands are described starting on

page 167

.

diagnose

Runs a diagnostic utility to conduct a series of internal checks and loopback tests to verify

network connectivity over each interface on your Motorola Netopia® Gateway. The console

displays the results of each test as the diagnostic utility runs. If one test is dependent on

another, the diagnostic utility indents its entry in the console window. For example, the

diagnostic utility indents the Check IP connect to Ethernet (LAN) entry, since that test will

not run if the Check Ethernet LAN Connect test fails.

Page 172 / 351

172

Each test generates one of the following result codes:

download [

server_address

] [

ﬁlename

] [conﬁrm]

This command installs a ﬁle of conﬁguration parameters into the Motorola Netopia® Gate-

way from a TFTP (Trivial File Transfer Protocol) server. The TFTP server must be accessible

on your Ethernet network.

You can include one or more of the following arguments with the download command. If

you omit arguments, the console prompts you for this information.

•

The

server_address

argument identiﬁes the IP address of the TFTP server from

which you want to copy the Motorola Netopia® Gateway conﬁguration ﬁle.

•

The

filename

argument identiﬁes the path and name of the conﬁguration ﬁle on the

TFTP server.

•

If you include the optional

conﬁrm

keyword, the download begins as soon as all infor-

mation is entered.

You can also download an SSL certiﬁcate ﬁle from a trusted Certiﬁcation Authority (CA), on

platforms that support SSL, as follows:

download [-cert] [

server_address

] [

ﬁlename

] [conﬁrm]

install [

server_address

] [

ﬁlename

] [conﬁrm]

(Not supported on model 3342/3352)

Downloads a new version of the Motorola Netopia® Gateway operating software from a

TFTP (Trivial File Transfer Protocol) server, validates the software image, and programs the

image into the Motorola Netopia® Gateway memory. After you install new operating soft-

ware, you must restart the Motorola Netopia® Gateway.

CODE

Description

PASS

The test was successful.

FAIL

The test was unsuccessful.

SKIPPED

The test was skipped because a test on which it depended failed, or

because the test did not apply to your particular setup or model.

PENDING

The test timed out without producing a result. Try running the test again.

Page 173 / 351

173

SHELL Commands

The

server_address

argument identiﬁes the IP address of the TFTP server on which

your Motorola Netopia® Gateway operating software is stored. The

filename

argument

identiﬁes the path and name of the operating software ﬁle on the TFTP server.

If you include the optional keyword

confirm

, you will not be prompted to conﬁrm whether

or not you want to perform the operation.

license [key]

This command installs a software upgrade key. An upgrade key is a purchased item, based

on the serial number of the gateway.

log

message_string

Adds the message in the

message_string

argument to the Motorola Netopia® Gateway

diagnostic log.

loglevel [

level

]

Displays or modiﬁes the types of log messages you want the Motorola Netopia® Gateway

to record. If you enter the

loglevel

command without the optional

level

argument,

the command line interface displays the current log level setting.

You can enter the

loglevel

command with the

level

argument to specify the types of

diagnostic messages you want to record. All messages with a level number equal to or

greater than the level you specify are recorded. For example, if you specify loglevel 3, the

diagnostic log will retain high-level informational messages (level 3), warnings (level 4),

and failure messages (level 5).

Use the following values for the

level

argument:

•

1

or

low

– Low-level informational messages or greater; includes trivial status mes-

sages.

•

2

or

medium

– Medium-level informational messages or greater; includes status mes-

sages that can help monitor network trafﬁc.

•

3

or

high

– High-level informational messages or greater; includes status messages

that may be signiﬁcant but do not constitute errors.

•

4

or

warning

– Warnings or greater; includes recoverable error conditions and useful

operator information.

Page 174 / 351

174

•

5

or

failure –

Failures; includes messages describing error conditions that may

not be recoverable.

netstat -i

Displays the IP interfaces for your Motorola Netopia® Gateway.

netstat -r

Displays the IP routes stored in your Motorola Netopia® Gateway.

nslookup {

hostname

|

ip_address

}

Performs a domain name system lookup for a speciﬁed host.

•

The

hostname

argument is the name of the host for which you want DNS information;

for example,

nslookup klaatu

.

•

The

ip_address

argument is the IP address, in dotted decimal notation, of the device

for which you want DNS information.

ping [-s

size

] [-c

count

]{

hostname

|

ip_address

}

Causes the Motorola Netopia® Gateway to issue a series of ICMP Echo requests for the

device with the speciﬁed name or IP address.

•

The

hostname

argument is the name of the device you want to ping; for example,

ping

ftp.netopia.com

.

•

The

ip_address

argument is the IP address, in dotted decimal notation, of the device

you want to locate. If a host using the speciﬁed name or IP address is active, it returns

one or more ICMP Echo replies, conﬁrming that it is accessible from your network.

•

The

-s

size

argument lets you specify the size of the ICMP packet.

•

The

-c

count

argument lets you specify the number of ICMP packets generated for the

ping request. Values greater than 250 are truncated to 250.

You can use the

ping

command to determine whether a hostname or IP address is

already in use on your network. You cannot use the

ping

command to ping the Motorola

Netopia® Gateway’s own IP address.

Page 175 / 351

175

SHELL Commands

quit

Exits the Motorola Netopia® Gateway command line interface.

reset arp

Clears the Address Resolution Protocol (ARP) cache on your unit.

reset atm

Resets the Asynchronous Transfer Mode (ATM) statistics.

reset cdmode

This command will set up one boot ﬂag so that the next time a 3342

N

/3352

N

restarts or

reboots (power cycle), the Gateway will boot into CD-ROM mode instead of Gateway mode.

This command is only for the 3342

N

/3352

N

. If the Gateway is not a 3342

N

/3352

N

this

command does nothing but returns the message: “CD mode is not supported on this plat-

form.”

reset crash

Clears crash-dump information, which identiﬁes the contents of the Motorola Netopia®

Gateway registers at the point of system malfunction.

reset dhcp server

Clears the DHCP lease table in the Motorola Netopia® Gateway.

reset diffserv

Resets the Differentiated Services (diffserv) statistics.

reset enet [ all ]

Resets Ethernet statistics to zero. Resets individual LAN switch port statistics as well as

wireless and WAN Ethernet statistics (where applicable).

Rate

Popular Motorola Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share