Page 61 / 76
Scroll up to view Page 56 - 60
MWN-WAPR150N Wireless Router
±
URL Strings:
Specify the text strings or keywords
needed to be filtered. If any part
of
the
URL
contains these strings or words, the web page will not be
accessible and displayed.
±
Times:
Select the time range of client filter.
±
Days:
Select the day(s) to run the access policy.
10.3 MAC Address Filter (Parental Control)
Limit or Control Access to the internet for specific computers
on the network at certain times of the day.
For example:
The example below shows “Jack’s PC” will not
have internet access from 10:00pm to 6am everyday.
57
Page 62 / 76
MWN-WAPR150N Wireless Router
±
MAC Address Filter:
Check to enable MAC address
filter.
±
Access Policy:
Select one number from the drop-down
menu.
±
Enable:
Check to enable the access policy.
±
Clear the Policy:
Click “Clear” button to clear all
settings for the policy.
±
Filter Mode:
Click one radio button to enable or disable
to access the Internet.
±
Policy Name:
Enter a name for the access policy
selected.
±
MAC Address:
Enter the MAC address you want to
run the access policy.
±
Times:
Select the time range of client filter.
±
Days:
Select the day(s) to run the access policy.
±
Apply
：
Click to make the settings go into effect.
10.4 Prevent Network Attack (Firewall)
This section is to protect the internal network from exotic
attack such as SYN Flooding attack, Smurf attack, LAND
attack, etc. Once detecting the unknown attack, the Router
will restrict its bandwidth automatically.
The attacker’s IP address can be found from the “System
58
Page 63 / 76
MWN-WAPR150N Wireless Router
Log”.
Prevent Network Attack:
Check to enable it for attack
prevention.
10.5 Remote Web Management
This section is to allow the network administrator to manage
the Router remotely. If you want to access the Router from
outside the local network, please select the “Enable”.
±
Enable:
Check to enable remote web management.
±
Port:
The management port open to outside access. The
default value is 8080.
±
WAN IP Address:
Specify the range of the WAN IP
address for remote management.
59
Page 64 / 76
MWN-WAPR150N Wireless Router
Note
：
1. If you want to login the device’s Web-based
interface via port 8080, you need use the format of
WAN
IP
address:
port
(for
example
8080)
to
implement
remote login.
2.
If your WAN IP address starts and ends with
0.0.0.0, it means all hosts in WAN can implement
remote Web management. If you change the WAN
IP address as 218.88.93.33-218.88.93.35, then
only
the
IP
addresses
as
218.88.93.33,
218.88.93.34 and 218.88.93.35 can access the
Router.
For example:
If you want to configure the IP address 218.88.93.33 to
access the device’s web interface, please set it as follows:
10.6 WAN Ping
The ping test is to check the status of your internet
connection. When disabling the test, the system will ignore
the ping test from WAN.
60
Page 65 / 76
MWN-WAPR150N Wireless Router
±
Ignore Ping from WAN:
Check to ignore the ping
request and give no reply.
Chapter11 Routing Setting
11.1 Routing Table
The main duty for a router is to look for a best path for every
data frame, and transfer this data frame to a destination. So,
it’s essential for the router to choose the best path, i.e.
routing arithmetic. In order to finish this function, many
transferring paths, i.e. routing table, are saved in the router,
for choosing when needed.
61
19216811.live