Page 41 / 165
Scroll up to view Page 36 - 40
31
Chapter 6: Setting up the Wireless-G Router for Broadband WAN Service Only
Using the Setup Wizard
Wireless-G Router for 3G/UMTS Broadband
8.
Connect the included Ethernet network cable to the Ethernet network port of your computer. (This cable is
color-coded yellow to match the yellow Ethernet ports on the Router.)
Click the
Next
button.
9.
Connect the other end of the cable to one of the Ethernet ports labeled 1-4 on the side panel of the Router.
Connect additional computers or other devices to the Router.
Click the
Next
button.
Figure 6-6: Connect the Router to a Computer Screen
Figure 6-7: Connect the Router to a Computer Screen,
continued
Downloaded from
www.Manualslib.com
manuals search engine
Page 42 / 165
32
Chapter 6: Setting up the Wireless-G Router for Broadband WAN Service Only
Using the Setup Wizard
Wireless-G Router for 3G/UMTS Broadband
10. Connect the power adapter to the Router’s Power port. Plug the other end into an electrical outlet.
Click the
Next
button.
11. Make sure the Power, Internet, and at least one of the numbered LEDs on the Router light up. If they do not
light up, make sure the cables are securely connected.
The Power LED will flash for a few seconds while the Router goes through its self-diagnostics test. This LED
will be solidly lit when the self-test is complete. If it does not stop flashing, refer to “Appendix A:
Troubleshooting.”
Click the
Next
button.
Figure 6-8: Power on the Router Screen
Figure 6-9: Check the Router’s Status Screen
Downloaded from
www.Manualslib.com
manuals search engine
Page 43 / 165
33
Chapter 6: Setting up the Wireless-G Router for Broadband WAN Service Only
Using the Setup Wizard
Wireless-G Router for 3G/UMTS Broadband
12. Select the Internet connection type you use:
Cable (DHCP)
,
DSL (PPPoE)
, or
Static IP
. Proceed to the
appropriate section for your Internet connection type.
Cable (DHCP)
Click the
Next
button.
DSL (PPPoE)
User Name
- Enter the User Name provided by your ISP.
Password
- Enter the Password provided by your ISP.
Confirm
- To confirm the Password, enter it again in this field.
Click the
Next
button to continue.
Figure 6-10: Configure Cable or DHCP Settings Screen
Figure 6-11: Configure DSL (PPPoE) Settings Screen
NOTE:
If the Internet connection type you use is not listed here, keep the default,
Cable (DHCP)
for now, and click the
Next
button. After you have completed the Setup Wizard, go to “Chapter 8:
Configuring the Wireless-G Router for 3G/UMTS Broadband.” You will use the Router’s web-
based utility to configure the Internet connection type settings.
Downloaded from
www.Manualslib.com
manuals search engine
Page 44 / 165
34
Chapter 6: Setting up the Wireless-G Router for Broadband WAN Service Only
Using the Setup Wizard
Wireless-G Router for 3G/UMTS Broadband
Static IP
IP Address
- Enter the IP address provided by your ISP.
Subnet Mask
- Enter the Subnet Mask provided by your ISP.
Gateway
- Enter the Gateway IP address provided by your ISP.
DNS 1-2
- Enter the DNS (Domain Name System) server IP address(es) provided by your ISP. You need to enter
at least one DNS address.
Click the
Next
button to continue.
13. The Setup Wizard will ask you to review your settings before it saves them. Click the
Yes
button if you are
satisfied with your settings, or click the
No
button if you do not want to save the new settings.
Figure 6-12: Enter Static IP Address Settings Screen
Figure 6-13: Confirm New Settings Screen
Downloaded from
www.Manualslib.com
manuals search engine
Page 45 / 165
35
Chapter 6: Setting up the Wireless-G Router for Broadband WAN Service Only
Using the Setup Wizard
Wireless-G Router for 3G/UMTS Broadband
14. The Router provides a web-based utility you can use for configuring the Router from any networked PC.
Password
- Enter a password that will control access to the Utility.
Confirm
- Then enter it again in the
Confirm
field.
Click the
Next
button.
15. The Setup Wizard will ask you to enter the settings for your wireless network.
Wireless Network Name
- In the
Wireless Network Name
field, enter the name of your wireless network,
also called the SSID. The name must be identical for all devices in the network. The default setting is
linksys
(all lowercase).
Channel
- Select the operating channel for your wireless network. All of your wireless devices will use this
channel to communicate.
Click the
Next
button.
Figure 6-14: Set the Router’s Password Screen
Figure 6-15: Wireless Settings Screen
Downloaded from
www.Manualslib.com
manuals search engine
19216811.live